Cortalk uDL1 Configuration & Operation Manual Download Page 2

Page: 2 / 26

MOBILTEX® DATA LTD.

Calgary, Alberta

www.corTalk.com

TITLE:

uDL1 Configuration and Operation Guide

DOCUMENT NO.:

UDL1-MAN-001

SHEET:

2 of 26

REV:

1.07

RESTRICTED PROPRIETARY INFORMATION

This information disclosed herein is the exclusive property of Mobiltex

Data Ltd. and is not to be disclosed without the

written consent of Mobiltex

Data Ltd. No part of this publication may be reproduced or transmitted in any form or by

any means including electronic storage, reproduction, execution or transmission without the prior written consent of
Mobiltex

Data Ltd. The recipient of this document by its retention and use, agrees to respect the security status of the

information contained herein.

This document is intended for limited circulation.

The information contained in this document is subject to change without notice and should not be construed as a
commitment by Mobiltex

Data Ltd. unless such commitment is expressly given in a covering document. Mobiltex

and corTalk

are registered trademarks of Mobiltex

Data Ltd.

CURRENT REVISION APPROVALS (Revision 1.07)

Name

Location

Job Function

Signature

Date

Tony da Costa

Calgary

Engineering Manager

Jerry Chilibecki

Calgary

Director of Engineering

REVISION HISTORY

Rev

Start Date

Approval
Date

Description

Prepared By

Draft
0.01

Sept 26, 2011

First draft.

Tony da Costa

1.00

Oct 14, 2011

Initial release.

Tony da Costa

1.01

Dec 15, 2011

Additional operational descriptions.

Updated screen shots to most recent configuration application version.
Updated accuracy specifications.

Tony da Costa

1.02

July 9, 2012

Updated screen shots to most recent configuration application version.

Added time display description.

Updated pictures of kit contents.

Added limitation statement regarding monitoring of interruption
waveforms.

Added calibration date information.

Added firmware update procedure.

Tony da Costa

1.03

April 10, 2013

Updated driver install procedure for new FTDI driver installer.

Updated software install procedure for new composite uDL1/2 media.

Tony da Costa

1.04

Dec 5, 2013

Updated high-range specifications

Tony da Costa

1.05

Nov 24, 2014

Added information for new features in v1.11 firmware.

Tony da Costa

1.06

Dec 7, 2017

Added clarification on calibration intervals.

Tony da Costa

1.07

Jan 29, 2018

Added G2 hardware information, including new interruption tracking
capability. Updated specifications.

Tony da Costa

Summary of Contents for uDL1



























Search results

Summary of Contents for uDL1

Reviews:

Cortalk uDL1, Configuration & Operation Manual, Page: 2 / 26

Search results

Summary of Contents for uDL1

Reviews: