background image

24 – Corning Lambda EliteTouch Pipettors 

INSTRUCTION MANUAL – 25

For your reference, make a note of the model number, serial 

number, date of purchase, and supplier here.
Model No. 

Serial No. 

Date Purchased 

Supplier

13. Warranty Statement

Corning Incorporated (Corning) warrants that this product 

will be free from defects in material and workmanship for 

a period of three (3) years from date of purchase. CORNING 

DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED 

OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF 

MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR 

PURPOSE. Corning’s sole obligation shall be to repair or 

replace, at its option, any product or part thereof that 

proves defective in material or workmanship within the 

warranty period, provided the purchaser notifies Corning 

of any such defect. Corning is not liable for any incidental 

or consequential damages, commercial loss or any other 

damages from the use of this product.
This warranty is valid only if the product is used for its 

intended purpose and within the guidelines specified in the 

supplied instructions manual. This warranty does not cover 

damage caused by accident, neglect, misuse, improper 

service, natural forces or other causes not arising from 

defects in the original material workmanship. This warranty 

does not cover the PTFE seal, O-ring, or shaft. Claims for 

transit damage should be filed with the transportation 

carrier.

In the event this product fails within the specified period 

of time because of a defect in material or workmanship, 

contact Corning Customer Service at: USA/Canada 

1.800.492.1110, outside the U.S.+1.978.442.2200, visit 

www.corning.com/lifesciences

, or contact your local 

support office.

Corning Customer Service will help arrange local service 

where available or coordinate a return authorization 

number and shipping instructions. Products received 

without proper authorization will be returned. All items 

returned for service should be sent postage prepaid in 

the original packaging or other suitable carton, padded to 

avoid damage. Corning will not be responsible for damage 

incurred by improper packaging. Corning may elect for 

onsite service for larger equipment.
Some states do not allow limitation on the length of 

implied warranties or exclusion or limitation of incidental 

or consequential damages. This warranty gives you specific 

legal rights. You may have other rights which vary from state 

to state.
No individual may accept for, or on behalf of Corning, any 

other obligation of liability, or extend the period of this 

warranty.

Summary of Contents for Lambda EliteTouch


















Reviews: