UNIV
Lace Align - TLSO
35-3300
Sizing
25"- 45"
Extension Kit-16"
35-3904
1.
Loosen both shoulder straps and slide brace onto shoulders, similar to
applying a backpack. Center the back panel on the lower back.
2.
Slide fingers through the loops on the belt ends to aid application.
3.
Wrap belt around abdomen and overlap ends, right over left. Press firmly
to engage hook and loop closure. When applied correctly, brace should fit
snug at top and bottom. If there is a gap, reapply and angle ends to ensure
a snug fit at upper/lower edges.
1.
Slide thumbs through pull-tab holes and pull them away from the body.
Right pull-tab controls lower compression and left pull-tab controls upper
compression.
2.
Apply tension until desired support is achieved.
2.
Positioning and applying the brace
GM-5053-000
Care instructions:
Product should be hand washed only using warm water and detergent for
delicate fabrics, repeatedly rinsed and line dried only. Do not use bleach or
place in a dryer. Plastic/foam back panels can be cleaned using warm water
and a mild disinfectant. Do not immerse brace in liquids.
Caution:
This product has been designed and tested for single patient use only. It
should never be used by multiple patients. If additional pain or symptoms
occur while using the device, seek medical attention. Product should be
applied by a licensed or certified healthcare practitioner and as prescribed
by a physician or other qualified medical authority. Brace is not meant to be
worn during sleep or while bathing.
Indications:
Indicated for lower back pain, sprains/strains, kyphosis, decompressive
procedures, degenerative disc disease, bulging/herniated discs,
compression fractures, post-op stabilization, spondylolisthesis, spinal
stenosis, spondylosis, or severe DJD
Contraindications:
Contraindicated for unstable, displaced fractures, women who are
pregnant, persons with circulatory, pulmonary, cardiovascular or other
conditions where increased abdominal pressure could worsen risks.
Warranty:
Products manufactured by Corflex are warranted to the original purchaser
against defects in workmanship and material for the life of the product. The
foregoing warranty shall not apply to normal wear and tear; or if the
product has been subjected to misuse or misapplication the warranty will
be voided at the discretion of Corflex.
A P P L I C A T I O N I N S T R U C T I O N S ( c o n t ’ d )
CORFLEX, INC. 669 EAST INDUSTRIAL PARK DRIVE, MANCHESTER, NH 03109
WWW.CORFLEX.COM TOLL FREE: 800 426 7353 FAX: 603 623 4111
To Reorder:
Designed for life.
Sizing: Fits waist circumference of 25” to 45”, use Extension Kit for circ. up to 70". .
Measurement taken from waist/hip circumference. Use larger of the two circumferences.
Product Number
Accessories
1.
Sternum Strap improves comfort by pulling the shoulder straps away
from the axilla. Fasten buckle and tighten strap for a comfortable fit.
2.
Sternum Strap can also be removed completely if desired. Buckle is
slotted to facilitate removal/reapplication without cutting any strapping.
3.
Adjust Shoulder Straps at top buckle (near axilla). Pull to tighten until
straps fit properly and desired degree of spinal extension is achieved.
4.
Straps should not be too tight as to cause discomfort or dig into axilla.
1.
Wrap pull-tabs around the front of the brace, securing to loop on the
outside of the brace.
2.
For comfort while seated, lessen tension on the upper portion of the
back panel (left pull-tab). Reapply tension upon rising.
3.
When removing the brace, lift pull-tabs to release tension and
relocate them to the ready position as shown in Step 1.
3.
Tightening the brace
4.
Adjusting harness and sternum strap
5.
Adjustment and removal
