Setup Bar and flying lines
The new Core SENSOR BAR is ready
for plug & play. Just unwind your lines,
attach them to the kite and have fun! The
following instructions and the picture on
the left should give you a quick overview
how to setup your new kite and bar.
PREFLIGHT CHECKLIST
1. Make sure your launch is open, FREE OF
DOWNWIND BYSTANDERS, hard objects, nearby
power lines, buildings and walls, within at least
200 ft. (60 m), and preferably more. Some riders
have needed in excess of 500 ft. (170 m), to re-
gain control in violent dragging or loftings. Avoid
kiteboarding near airports and in low flight path
areas, complaints have led to restricted access
in some areas.
2. Check to see what size kite other kiteboarders
are rigging and get their input on conditions. Do
not rig too large a kite for conditions and careful-
ly consider advice of more experienced riders.
Failure to act on prudent advice has cost some
riders severe injury.
3. Check your kite for tears or leaky bladders. If
you have leaky bladders or tears in your kite,
repair them before flying.
4. Check ALL kite, harness, control bar lines,
webbing, pigtails, bridles, the chicken loop and
leaders for knots, wear or abrasions. If the line
sheathing shows any breaks, replace them. The
pigtails should be replaced no less frequently
than every 6 months on inflatable kites. Inspect
and test all your quick releases.
5. Make sure your flying lines are equal as they
will stretch unevenly with use. If they have knots
that can´t be easily untied, replace your flight
lines.
6. Walk down your lines and examine them care-
fully. Just before launch pick your bar up and
carefully look down the lines for twists and
tangles that could cause the kite to be dange-
rously uncontrollable. While you are holding
your bar up look down the lines, shake your bar
to make sure the center lines are connected to
the leading edge of the kite. Be particularly care-
ful, slow and methodical in high winds. Multiple,
careful preflighting in higher winds is strongly
advised.
Inflate the kite to 6-7 psi and close the Fast-
Pump-Clamps properly.
To depower the kite with the adjuster , always
keep a little tension on the backlines.
Before starting the kite you should allways
check all bar safety systems and feel comfortab-
le with all features on the bar.
Double-check the weather conditions and if
you´re in doubt, don´t go out!
Have fun and enjoy your safe ride!
Short manual:
CORE RIOT XR and
CORE SENSOR BAR
Download the detailed user manual from
11
16
10
14
17
12
13
1
2
5
8
9
6
7
4
3
15
N
E
S SORBARSYSTEM
L
M
4
2
EINEN/LINES / 52/45CM
1
Connector-Leinen/Connector Lines
K20370
2
Steuerleinen/Steering Lines
20M K20373 / 24M K20375 / 31M K20377
3
Front-Leinen/Front Lines
20M K20372 / 24M K20374 / 31M K20376
4
Y-Pulley
K20378
5
Power-Leine/Power Line
K20379
6
Virtuelle 5te Leine/Virtual 5th Line
K20380
7
Vorleinen/ Leader Lines
K20381
8
Depower-Leine/Depower Line
K20384
9
Sensor Adjuster
K20382
9.
a
Adjuster Grip
K20382
9.
b
Adjuster Cover
K20382
10
Vorleinen-Justierleine/
Leader Adjustment Line
K20381
11
Schwimmer/Floater
K20383
12
Sensor Auslösesystem/Sensor Release
K20385
13
Chickenstick
K20372
14
Sensor Control Bar
K20390
15
Sensor Stopper (optional)
K20391
16
Sensor Short Leash
K20388
17
Sensor Pro Leash (optional)
K20389
