background image

TUBULAR SHOWER PANELS

PAGE 1

00 71277 00 / Issue 6 / 10

Please read these instructions carefully and keep for future reference. 
Incorrect fitting will invalidate the guarantee.

SAFETY

● 

Handle glass with care. Sharp impacts can damage the metal components and 
could shatter the glass.

 Do not remove the plastic corner protectors from the glass panels until the panels 

are about to be fitted.

● 

As the parts are large, we recommend that two people are needed to carry out  
parts of the installation.

● 

Make sure there are no hidden pipes or cables in the floor and walls where you 
intend to drill.

● 

Wear safety goggles, shoes and appropriate clothing.  

BEFORE INSTALLATION

● 

The enclosure will not sit correctly on an uneven surface. If uneven, the wall 
channels may not fit. 

● 

Note:

 

If not fitted on a tray, ensure the enclosure is fitted to a tiled or 

waterproof composite floor.

● 

The enclosure should be fitted on tiled walls which are sealed with waterproof grout. 

● 

Always check very carefully that components are vertical.

● 

To avoid damage, use the opened out packaging to build the enclosure on.

EQUIPMENT NEEDED:

Drill, 6mm Masonry Bit, 3mm Metal Bit (general), Crosshead Screwdriver, Spirit Level, 
Pencil, Fine Tooth Saw, Silicone Sealant, Scissors, Tape Measure.

Note: The screws and wall plugs supplied are for masonry walls. For lightweight  
walls i.e. stud partitions, plasterboard etc, use the correct type of fixings.

SINGLE PANEL - PAGES 2 - 4

DOUBLE PANEL - PAGES 4 - 9

2

1

2

1

2

1

1

1

2

1

4

2

2

1

2

1

2

1

10

5

4

2

PANELS:

2

1

2

1

10

5

10

5

PN60159 

Grub screw

PN50247 

Top cap

PN60162 

3mm  

Allen key

PN80456

Outer  

ceiling bracket

Assemble

PN60154 

Strut  

bracket 

PN60210

 

Wall plug

PN40063 

Seal

PN60320 

16mm

Screw

PN60312 

38mm

Screw

PN8212 

Washer

CUSTOMER CARELINE: 01746 713410

Check contents of the pack before installation. If there is anything missing, contact our Customer Care Number for assistance. 

The fixings may be spread across several packs - please check the contents of each pack carefully. 

PANELS:

PANELS:

PANELS:

PANELS:

2

1

2

1

2

1

PN60163

Tube cap

PN80480

Panel 

bracket/

Glass clamp

PANELS:

Vertical Strut Option

Vertical Strut Option

Summary of Contents for TUBULAR SHOWER PANELS










Reviews: