background image

2÷8 Ohm Speakers

SPEAKER

+

-

+

-

+

-

1÷4 Ohm Speakers

SPEAKER

+

-

+

-

USCITA ALTOPARLANTI

L’amplificatore dispone di una doppia morsettiera, per facilitare 
l’eventuale collegamento di due subwoofer. Collegate gli alto-
parlanti con cavo di buona qualità, rispettando le polarità. La 
sezione del cavo deve essere adeguata alla sua lunghezza ed 
alla potenza, come da tabella a pagina 5.

Verificate  attentamente  che  l’impedenza  di  carico 

non

  sia 

inferiore  a  quella  accettata  dall’amplificatore. 

Non

  collega-

te mai insieme i negativi, 

non

 collegate mai a massa alcun 

altoparlante.

LOUDSPEAKER OUTPUT

The  amplifier  is  equipped  with  a  double  terminal  block, 
to make a possible link of a subwoofer pair easy. Link the 
speakers by using high quality cables, keeping the polarities. 
The wire gauge needs to be adapted to it’s length and used 
power, as on table of page 5.

Make sure that the load’s impedance is 

not

 lower then the 

accepted  one  from  your  amplifier. 

Never

  link  together  the 

negatives  of  the  speakers, 

never

  connect  to  ground  any 

loudspeakers.

130.com.ua

Autogood products «130»

Summary of Contents for XTA 130


























Reviews: