311
TRACK
LIGHTING
Single Circuit
COOPER LIGHTING
HALO
®
L 9 0 4
L C o n n e c t o r
To connect two track sections at a right angle.
Field adjustable for either right hand or left hand
application. May be used as feed point.
Finish:
White (P), Black (MB)
L 9 0 6
X C o n n e c t o r
To connect four track sections into a cross
configuration. May be used as feed point.
Finish:
White (P), Black (MB)
L 9 0 8
M i n i J o i n e r
A low profile connector to cleanly and crisply
join two straight track sections end-to-end.
(Note: The L908 is not a feed point).
Finish:
White (P), Black (MB)
L 9 5 0
C o r d a n d P l u g C o n n e c t o r
12’ three-wire cord with grounded plug.
Maximum capacity 10 AMP
Finish:
White (P), Black (MB)
L 9 7 9
C o n d u i t C o n t i n u a t i o n K i t
Consisting of one left feed and one right feed.
To continue a run around obstructions. Designed
to accept 1/2” trade size conduit fitting (not
included).
Finish:
White (P), Black (MB)
L 9 8 3
T- B a r A t t a c h m e n t C l i p
Allows track to be attached to inverted tee ceiling.
Order as follows: 2 kits for 2’ Trac; 2 kits for 4’
Trac; 3 kits for 8’ Trac and 4 kits for 12’ Trac.
L 9 8 6
M i n i - T B a r C l i p
For mounting Trac on suspended ceilings with
mini-grid (9/16” wide) system.
L 9 9 4
4 5 ° P e n d a n t A d a p t e r
For installing pendant mounted Power-Trac on
sloped ceiling. For use with L992 and L993.
Finish:
White (P), Black (MB)
L 9 0 5
T C o n n e c t o r
To connect three track sections into a T
configuration. Field adjustable for either right
hand or left hand application. May be used as
feed point.
Finish:
White (P), Black (MB)
L 9 0 7
O u t l e t B o x f o r u s e w i t h
T- B a r c e i l i n g
L901, L903, L904, L905 or L906 connector also
required. 4”x 4” x 1 1/8”.
Finish:
White (P), Black (MB)
L 9 0 9
F l o a t i n g C a n o p y a n d
C o n n e c t o r
Track can be connected to existing outlet
box located anywhere along the track. Comes
with canopy cover, connector, dead-end and
mounting hardware. 4 1/8” x 4 1/4” x 1 3/8”.
Finish:
White (P), Black (MB)
L 9 5 1
W i r e W a y C o v e r f o r P e n d a n t
A s s e m b l y K i t
For track to be wired through stem (order one
for each feed point used). Shown with end
feed and pendant stem kit–order separately
Finish:
White (P), Black (MB)
L 9 8 0
L i v e E n d C o n d u i t A d a p t e r
Designed to accept standard 1/2” trade size
conduit fitting (not supplied). Use when
feeding to track through surface conduit
system.
Finish:
White (P), Black (MB)
L 9 9 2
P e n d a n t K i t A s s e m b l y
Order 2 kits for 2’ Trac; 2 kits for 4’ Trac; 3 kits
for 8’ Trac; and 4 kits for 12’ Trac. Includes one
18” threaded steel stem, canopy and mounting
hardware.
L 4 8 4 8 ” S t e e l S t e m
For additional length with L992. Can be field cut.
Finish:
White (P), Black (MB)
D E 6 0 0 D e a d E n d
Replacement Dead Ends for Single Circuit Track
(6 included)
Finish:
White (P), Black (MB)
