manualshive.com logo in svg

Cooper Lighting AtLite AUX Series, Installation Instructions Manual, Page: 6 / 6

Share
Download
Cooper Lighting AtLite AUX Series Installation Instructions Manual Download Page 6

Cooper Lighting Solutions 

1121 Highway 74 South

 

Peachtree City, GA 30276

P:770-486-4800

www.cooperlighting.com

© 20

20

 

Cooper Lighting Solutions

All Rights Reserved

Printed in USA

Publication No. ADA140172

Cooper Lighting Solutions

 is a 

registered trademark.

All trademarks are property  

of their respective owners.

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY

The information, recommendations, descriptions and safety notations in this document are based on 

Cooper Lighting 

Solutions

 Corporation’s (“

Cooper Lighting Solutions

”) experience and judgment and may not cover all contingencies. If 

further information is required, an 

Cooper Lighting Solutions

 sales office should be consulted. Sale of the product shown in 

this literature is subject to the terms and conditions outlined in appropriate 

Cooper Lighting Solutions

 selling policies or other 

contractual agreement between 

Cooper Lighting Solutions

 and the purchaser.

THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES 

OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN 

ANY EXISTING CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE OBLIGATION OF 

COOPER LIGHTING SOLUTIONS

. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY 

CONTRACT BETWEEN THE PARTIES. 
In no event will 

Cooper Lighting Solutions

 be responsible to the purchaser or user in contract, in tort (including negligence), 

strict liability or other-wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not 

limited to damage or loss of use of equipment, plant or power system, cost of capital, loss of power, additional expenses in 

the use of existing power facilities, or claims against the purchaser or user by its customers resulting from the use of the 

information, recom-mendations and descriptions contained herein. The information contained in this manual is subject to 

change without notice. 

Summary of Contents for AtLite AUX Series







Reviews:

No comments