Cooper Lighting AtLite AUX Series Installation Instructions Manual Download Page 1

INS #

049-245

Installation Instructions for the AUX Universal Edge Lit Exit – 

Battery Backup with Self Diagnostics 

 WARNING 

Risk of Fire/Electric Shock

If not qualified, consult an electrician.

 WARNING 

Risk of Electric Shock

Disconnect power at fuse or circuit breaker before 

installing or servicing.

Important Safeguards

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED 

INCLUDING THE  FOLLOWING.
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Dry location only.  Do not use outdoors.
3. Do not use in hazardous locations, or near gas or electric heaters.
4. Do not let power supply cords touch hot surfaces.
5. Use caution when servicing batteries.  Battery acid can cause burns to skin and eyes.  If acid is spilled on skin

or in eyes, flush acid with fresh water and contact a physician immediately.

6. Do not use this equipment for other than the intended use.
7. Installation is to be performed only by qualified personnel.
8. Install in accordance with National Electric Code and local regulatory agency requirements.
9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
10. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering

by unauthorized personnel.

11. SAVE THESE  INSTRUCTIONS

ADAPTER

PLATE

HANGER

BAR

ASSEMBLY

COVER

PLATE

HANGER BARS

ADJUSTED FOR 5/8"

THICK DRYWALL

PIVOT

HOUSING

LOCKING

CLIP

TRIM

ASSEMBLY

PLASTIC

INSTALLATION

HOOK

ADAPTER

PLATE

GUIDE

BRACKET

HOUSING

TRIM PLATE

FIGURE 1

HOUSING

FIGURE 3

FIGURE 6

HOUSING

FIGURE 2

FIGURE 7

HOUSING

CANOPY

HOUSING

COVER PLATE

CANOPY

FIGURE 8

FIGURE 4

FIGURE 5

WIRE IN WIRE TRAP

For Recessed Installation

1. Turn off power supply.
2. Determine if the fixture will be mounted in the

ceiling or the wall.

3. Remove the screws securing the trim plate to the

housing (See Figure 1).  Place the trim assembly

and screws aside and save them for later

installation. It is not necessary to disconnect the

wire harness connecting the charger driver circuit

board to the LED board.  Instead, the trim plate

can be hung from the sliding plastic installation

hook (see figure 2).

ADAPTER

PLATE

HANGER

BAR

ASSEMBLY

COVER

PLATE

HANGER BARS

ADJUSTED FOR 5/8"

THICK DRYWALL

PIVOT

HOUSING

LOCKING

CLIP

TRIM

ASSEMBLY

PLASTIC

INSTALLATION

HOOK

ADAPTER

PLATE

GUIDE

BRACKET

HOUSING

TRIM PLATE

FIGURE 1

HOUSING

FIGURE 3

FIGURE 6

HOUSING

FIGURE 2

FIGURE 7

HOUSING

CANOPY

HOUSING

COVER PLATE

CANOPY

FIGURE 8

FIGURE 4

FIGURE 5

WIRE IN WIRE TRAP

Summary of Contents for AtLite AUX Series







Reviews: