Cooper Lighting Solutions HALO ALS4A40GY Page 2 Instruction Manual Download

Page: 2 / 6

SAVE THESE INSTRUCTIONS.

MOUNTING AND WIRING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect

power at fuse or circuit breaker before installing

or servicing.

NOTE:

This fixture is intended to be conduit connected to a properly installed and properly

grounded metal weatherproof junction box (not included). All conduit connectors, conduit,

and junction boxes (sold separately) should be cULus Listed suitable for wet locations.

1. Turn off the power at the main fuse/breaker box.

2. Using the pattern on the box, mark and drill holes

for mounting.

Note:

Mount this fixture in an upright

and level position.

3. Install the two bottom mounting screws (C) first,

leaving enough room between the mounting

screws and the mounting surface to accommo-

date mounting the fixture.

4. Screw the top mounting screw (C) into the

predrilled hole and back the screw out. This will

leave the hole threaded and make installation of

the fixture easier.

5. Remove the cover plate by loosening the two

mounting screws (F) inside the cover plate.

6. Remove access cover (B) from fixture (A). Install

the first conduit connector and conduit (sold

separately) into the access cover (B) (Fig. 1).

7. Feed supply wires into conduit. Attach ground

wire that is attached to fixture housing (A) to the

junction box earth ground wire.

8. Connect the black fixture wire to the black supply

wire (hot) with UL-approved wire connector (E).

Connect the white fixture wire to the white supply

wire (neutral) with UL-approved wire connector (E).

9. Attach access cover (B) to the light fixture (A)

using the 2 access cover mounting screws (F)

provided (Fig. 1).

Note:

Make sure all wiring is

placed into the arm prior to tightening the access

cover screws to avoid pinching the wires.

10.Place the fixture (A) on the two lower mounting

screws (C) and install the upper mounting screw

(C). Tighten all mounting screws to secure the

fixture (A).

11.Reinstall the cover plate, making sure to tighten

the two screws to secure the lens to the fixture (A).

12.Connect second conduit and conduit connector

to the junction box (sold separately).

Note:

This fixture can be mounted on 1-5/8 in.

outside diameter extension arms (not provided).

When installing fixture onto an extension arm,

remove the access cover (B) and use the included

pole mounting clamp (D) and access cover

mounting screws (F) (Fig. 2).

13.Turn power back ON.

OPTIONAL: INSTALLING THE DROP REFRACTOR

Install the Drop Refractor (G) using the 2 drop

refractor mounting screws (H) in the parts bag.

Be careful to not overtighten the screws or use

power tools to tighten the screws.

NOTE:

If the fixture is Energy Star Certified, installing

the drop refractor will violate the fixture’s

Compliance.

TROUBLESHOOTING

Problem

Cause / Solution

Light Does Not

Come On or light

comes on for only

a few seconds

Light cycles

ON and OFF

continuously

Light does not

shut off during

daytime

No power to the fixture.

• Check if circuit breaker tripped.

• Confirm wall switch is ON.

Fixture is sensing daylight.

• Cover Photocontrol sensor. Unit will switch ON after a short delay.

TURN OFF POWER BEFORE CONTINUING

Wiring to the unit is loose.

• Confirm wiring is properly secured.

* If light still does not come on after checking wiring

connections, contact Customer Service.

Photocontrol sensor is sensing reflected light.

• Cover Photocontrol sensor with a piece of black electrical

tape. The fixture should turn on after a slight delay. This

means that extraneous or reflected light from the fixtures

causing the sensor to turn the unit off. Reflected light could

be coming from mounting the fixture too close to walls or

other objects that will throw the light into the sensor.

Relocate light fixture away from the object that was

reflecting light so it no longer cycles on and off.

Photocontrol sensor is in a shaded area.

• Shine a flashlight into the Photocontrol sensor. If the light

turns off, the fixture is mounted in an area that does not

allow enough light to enter the Photocontrol sensor

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Cooper Lighting Solutions warrants to customers that, for a period of five years from the date

of purchase, Cooper Lighting Solutions products will be free from defects in materials and

workmanship. The obligation of Cooper Lighting Solutions under this warranty is expressly

limited to the provision of replacement products. This

warranty is extended only to the original purchaser of the product. A purchaser’s receipt or

other proof of date of original purchase acceptable to Cooper Lighting Solutions. This is re-

quired before warranty performance shall be rendered. This warranty does not apply to Coo-

per Lighting Solutions products that have been altered or repaired that have been subjected

to neglect, abuse, misuse or accident (including shipping damages). This warranty does not

apply to products not manufactured by Cooper Lighting Solutions which have been supplied,

installed, and/or used in conjunction with Cooper Lighting Solutions products. Damage to the

product caused by replacement bulbs or corrosion or discoloration of brass components are

not covered by this warranty.

LIMITATION OF LIABILITY:

IN NO EVENT SHALL COOPER LIGHTING SOLUTIONS BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION,

WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR

FOR LOST PROFITS; NOR SHALL THE LIABILITY OF COOPER LIGHTING SOLUTIONS FOR ANY

CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANU-

FACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER

LIGHTING SOLUTIONS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,

EXCEED THE PURCHASE PRICE OF COOPER LIGHTING SOLUTION PRODUCTS GIVING RISE

TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

To obtain warranty service, please contact Cooper Lighting Solutions, at 1-800-334-6871,

press option 2 for Customer Service, or via e-mail [email protected]

and include the following information:

• Name, address and telephone number

• Date and place of purchase

• Catalog and quantity purchase

• Detailed description of problem

All returned products must be accompanied by a Return Goods Authorization Number issued

by the Company and must be returned freight prepaid. Any product received without a Return

Goods Authorization Number from the Company will be refused. Cooper Lighting Solutions is

not responsible for merchandise damaged in transit. Repaired or replaced products shall be

subject to the terms of this warranty and are inspected when packed. Evident or concealed

damage that is made in transit should be reported at once to the carrier making the delivery

and a claim filed with them.

Reproductions of this document without prior written approval of Cooper Lighting Solutions are strictly prohibited.

For assistance, call 1-800-334-6871 or e-mail us at [email protected]

Printed in China

CONDUIT CONNECTOR

CONDUIT

E. WIRE CONNECTORS

ALS Integrated Photocell

Instruction Sheets Figures

1.065 LB

29.468 IN3

L MOD: E0439882

7/10/2020

ALS Integrated Photocell Instruction Sheets Fi

gures

TOLERANCE

GENERAL

DIMENSIONS THAT AFFECT

SAFE HANDLING OR

OPERATION

818.746 IN2

DEV/ZINT NO:

1 OF

ANGLES

± 1.0 °

ALL

PRODUCT MUST CONFORM TO ROHS

COOPER LIGHTING SOLUTIONS - CONFIDENTIAL AND PROPRIETARY

NOTICE TO PERSONS RECEIVING THIS DOCUMENT AND/OR TECHNICAL INFORMATION

THIS DOCUMENT, INCLUDING THE DRAWING AND INFORMATION CONTAINED THEREON, IS

CONFIDENTIAL AND IS THE EXCLUSIVE PROPERTY OF EATON, AND IS MERELY ON LOAN

AND SUBJECT TO RECALL BY COOPER LIGHTING SOLUTIONS AT ANY TIME. BY TAKING POSSESSION

OF THIS DOCUMENT, THE RECIPIENT ACKNOWLEDGES AND AGREES THAT THIS DOCUMENT CANNOT

BE USED IN ANY MANNER ADVERSE TO THE INTERESTS OF COOPER LIGHTING SOLUTIONS,AND THAT

NO PORTION OF THIS DOCUMENT MAY BE COPIED OR OTHERWISE REPRODUCED WITHOUT THE

PRIOR WRITTEN CONSENT OF COOPER LIGHTING SOLUTIONS. IN THE CASE OF CONFLICTING

CONTRACTUAL PROVISIONS, THIS NOTICE SHALL GOVERN THE STATUS OF THIS DOCUMENT.

Cooper Lighti

ng SolutionsTemplate Rev -

IP LEVEL:

REVISIONS

REV.

DESCRIPTION

DATE

CHANGE_NUMBER

APPROVED

FIGURE 1

B. ACCESS COVER

A. LIGHT FIXTURE

G. DROP REFRACTOR

C. MOUNTING SCREWS

D. POLE MOUNTING CLAMP

F. POLE MOUNTING CLAMP/ACCESS COVER MOUNTING SCREWS

2.125

[54]

1.375

2.750

[70]

USE FOR PACKAGING ARTWORK

H. DROP REFRACTOR MOUNTING SCREWS

FIGURE 2

THIRD ANGLE PROJECTION

MATERIAL:

METRIC (MM)

ENGLISH (IN)

.XX

.XXX
.X

.XX

.XXX

DIMENSIONS ARE IN INCHES

DIMENSIONS IN [ ] ARE IN MM

ELECTRONIC CAD DRAWING. DO

NOT REVISE MANUALLY.

SURFACE AREA:

DO NOT SCALE DRAWING

DRWN:

DATE

APPROVALS

± 0.040

± 0.020

± 0.010
± 1

± 0.5

± 0.25

x.x

DENOTES CRITICAL

DIMENSIONS AND

GAUGE CHECK POINTS

DENOTES FIRST PIECE

AND IN-PROCESS

INSPECTION

DENOTES FIRST

PIECE

INSPECTION ONLY

PART NUMBER

TITLE:

SIZE:

DWG NO:

REV:

SHEET

VOL:

WT:

SCALE:

FINISH:

APPR:

CHKD: