Cooper Bussmann BU-905U-L Installation Manual Download Page 23 | Manualshive

Page: 23 / 30

background image

www.cooperbussmann.com/BussmannWirelessResources

Cooper Bussmann BU-905U-L Wireless I/O Installation Manual

I

NSTALLING AND CONFIGURING THE UNIT

This section describes how to install and configure your unit and contains the following sections:

Section

Description

For more information, see …

Installing the unit

Describes how to physically install your unit.

Installing the unit on page 23.

Configuring your unit

Describes the different ways to configure your unit.

Configuring your units on page 24.

Testing your unit

Describes the Bussmann recommendations for testing your unit.

Testing your units on page 25.

For more information, see the next sections.

Installing the Unit

To install the unit:

1. Connect signals to the supplied terminals.

2. Connect the radio antenna.

3. Install DIN rail to mount the module.

4. Clip the module to the DIN rail:

You can now configure your unit. For more information, Configuring your units on page 24.

23

3A1580Rev1.7

«
...
21
22
23
24
25
...
»

Summary of Contents for BU-905U-L































Reviews:

No comments

Related manuals for BU-905U-L

Brand: Lanner Pages: 2

iW-RainboW-G30D

Brand: iWave Pages: 89

Brand: Vivotek Pages: 170

Brand: Rosewill Pages: 3

WGR614 - Wireless-G Router Wireless

Brand: NETGEAR Pages: 116

Brand: Juniper Pages: 2

SmartSwitch 8-slot

Brand: Cabletron Systems Pages: 150

LonWorks Communication Module LN-01

Brand: Delta Electronics Pages: 1

Brand: ZyXEL Communications Pages: 79

Brand: iGateWeb.com Pages: 6

Brand: Axis Pages: 98

Brand: ZALMAN Pages: 18

Brand: Procool Pages: 2

Brand: Keysight Technologies Pages: 106

Brand: ALIBI Pages: 232

Brand: Extreme Networks Pages: 51

Brand: Kontron Pages: 14

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands