Cooper & Hunter CHV-05SDLSP Operation Installation Maintenance Manual Download Page 3

i

This manual should be considered as a permanent part of the air conditioning equipment. Please keep it properly.

We pursue a policy of continuous improvement in design and performance of products. The right is therefore reserved 

to change specifications without notice.

Our company shall not be held responsible for any occasional damage to the air conditioner that arises during its 

operation in specific environment.

This air conditioner must be used as a general air conditioner, and shall not be used for drying clothes, freezing foods, 

cooling or heating and other purposes. 

Please don't install the air conditioner in the following environments. Otherwise, fire, machine deformation or failure may 

arise.

*

Places with spatter of oil (including machine oil).
Places with inflammable gases.

*

Places with sulfurated gases or silicon (e.g. hot spring, etc.).

*
*

Coastal areas with much salt or the places exposed to strong acids or bases
that may cause corrosion to machine.

Signal words (DANGER, WARNING, CAUTION, and NOTE) are used to indicate hazard seriousness. 
Definitions of the hazard levels are provided below with respective signal words.

IMPORTANT NOTICE

Do not orient the air outlet immediately to animals and plants, since this may cause adverse effects thereon.
The installation and service engineering have to comply with local standards, laws and regulations.

As an "appliance inaccessible to the public", the installation height of indoor unit of the air conditioner shall be at

least 98-27/64 in.(2.5m).

This air conditioner can only be installed by dealers or professionals. The installation by user may lead to water

leakage, electric shock or fire.

In case of any question, please consult the dealer or the service center designated by our company.


For environmental protection, please don't dispose of the product casually. Our company can provide recycling service 

based on relevant regulations, and provide replacement parts according to relevant standards.

Refer to the instruction manual for complete machine (outdoor unit) for product standard for indoor unit.

Refer to Installation & Maintenance Manual of outdoor unit for temperature operation range.

lease don t perform installation  or s suc  as refrigerant piping connection  drain pipe connection  and  iring connection.

iolations ma  result in s stem lea age  electrical failure or fire.

o not pour  ater into t e indoor or outdoor unit. 

is mac ine is an electric product t at ma  de elop serious electric

failure 

en e posed to  ater.

o not open t e ser ice co er of indoor or outdoor units  it out turning 

 t e main po er suppl  ot er ise  t is ma

ring a out serious safet  accident.

o not touc  or ad ust safet  de ices inside t e indoor or outdoor units. If t e  are touc ed or read usted  serious accident

ma  arise.

Refrigerant leakage may bring about oxygen deficit-induced respiratory difficulty. In case refrigerant leakage is detected,

please turn off the main switch immediately, extinguish any naked flame, and contact service dealer.

Ma e sure air tig tness test is performed.

Refrigerant R

 is non flamma le  non to ic  and odorless  and ma  produce to ic gases 

en e posed to open flame.

ince t is refrigerant gas is  ea ier t an air  it ma  result in lac  of o gen  t ere  leading to  reat ing difficulties 

en

t e area near t e ground is filled  it  t is gas.  erforming lea  detection and gas tig tness test  it  o gen  acet lene or

ot er flamma le and to ic gases ma  cause e plosion  so nitrogen is recommended for t is test.

e standards for safe refrigerant lea age in construction and s stem operation are determined  ased on local regulations

or standards.

se 

  it  medium or  ig er sensing speed 

  it  an operating time of  .  seconds or less  or electric s oc  or

fire ma  arise.

or installation  t e refrigerant piping must  e firml  connected  efore t e operation of compressor.  or repair  t e

refrigerant piping must  e mo ed   andled and remo ed after t e stop of compressor.

lease don t s ort circuit t e protecti e de ice  e.g.  t e pressure s itc  etc.  during operation  since t is ma  cause fire

or e plosion.

Summary of Contents for CHV-05SDLSP

























Reviews: