background image

 
 
 

Limited One Year Warranty 

 

CoolWorks Inc. warrants this product, to original purchaser, for one year from purchase date to be free of defects in material and 
workmanship. 
 
Should any defect be discovered within one year of date of purchase, CoolWorks Inc. agrees to repair or replace the defective part or 
product at no charge other than handling and return freight charges, provided said part or product is returned with all shipping charges 
prepaid to CoolWorks Inc., Service Department, 819 A Street, San Rafael, CA  94901, accompanied by proof of purchase and a letter 
detailing the nature of the defect.  The Customer Service Department of CoolWorks Inc. should be contacted prior to any action in the 
event it is possible to correct the defect without returning the unit. 
 
This warranty does not apply to any unit that has been tampered with, or to damages incurred through negligence in use, faulty 
packing, or mishandling in transit by any common carrier.  Your remedy does not include loss of aquatic life, cost of inconvenience, 
or damage due to product failure.  In no event shall CoolWorks Inc. be liable for incidental or consequential damages. 
 
This warranty gives you specific legal rights; you may also have other rights, which vary from state to state. 

 
 

 
 
Service Information 

 

To assure years of dependable service, our products are made with high quality materials and are thoroughly tested prior to shipment. 
 
At CoolWorks, your satisfaction with our products is our top priority.  Should you encounter any form of product failure, please contact our 
Customer Service Department: 
 

CoolWorks Inc. 

819 A Street 

San Rafael, CA  94901 

Phone:  (415) 485-5552 

Fax:   (415) 258-9963 

Email:     [email protected] 

w w w . c o ol w o r k si n c. c o m 

 
This device should be serviced only by properly trained repair technicians.   Please do not attempt to service this product yourself. 
 

CoolWorks and Ice Probe are registered trademarks of CoolWorks Inc

Summary of Contents for IceProbe IPAC-50W









Reviews: