background image

 

11 

REMOTE ENGINE CONTROL 

 

SELECTABLE HOURLY COLD-START MODE (1-4 HOURS) 

This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed 
run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern.  

 
TIMED SELF-START MODE – Exiting the Vehicle: 

 

1)  Engine should be running with the Key.  Press the Remote Start button for at least 1 second.  Lights will turn on 

signaling the remote start has turned on and doors will unlock. 

2)  Within 10 seconds press and release the valet/program button once for each hourly increment (1 time = 1hour, 

2X = 2 hours, 3X = every 3 hours, 4X = every 4 hours).  

3)  Parking Lights will turn ON when the button is pressed and flash once for each consecutive button press. 
4)  Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 
5)  Once outside the vehicle, press and release the remote start button to turn off engine. The parking lights will 

flash the number of times indicating the hourly increment for confirmation. The vehicle will start by itself at the 
selected hourly increment until driven with key or started via the remote control. 

IGN

SOLID

OFF

UNLOCK

PRESS 1 - 4 X

WITHIN 10 SEC.

LIGHTS FLASH 

for each press

   ENGINE TURNS OFF

FLASH Hour Increment

 

RESETTING TIMED SELF-START MODE: 

To reset the timed self-start mode, start vehicle using the ignition key or the remote control. 

Summary of Contents for RS1-G5

























Reviews: