COOL BOSS CB-12SL Installation And Operation Manual Download Page 27 | Manualshive

Page: 27 / 36

COOL BOSS CB-12SL Installation And Operation Manual Download Page 27

Cool Boss Evaporative Air Cooler

27

P/N 5900274 — August 2022 — Rev. A1

To store the Cool Boss

:

1.

Dry the Media or verify it is dry.

2.

Drain the Reservoir and wipe clean and dry.

3.

Unplug or disconnect from power and secure the electrical cord.

4.

Cover the Cool Boss to prevent dust build-up and store in a dry, protected area.

To test the GFCI incorporated into the Cool Boss Power Cord

:

Plug the cord into a properly grounded wall outlet. The indicator should be illuminated. Refer to the
figure below.
a.

If not, check the wall outlet for power.

b.

If power is present at the outlet, the Power Cord or the GFCI is defective and requires
replacement.

Press the small Test button. The Indicator should go out and no power should be available at the

Cool Boss.

Press the Reset Button and the Indicator should be illuminated again. The Cool Boss should now

be provided power and ready for use.

If the GFCI does not function, take the unit out of service, contact your dealer or Cool Boss
Support at

coolboss.com/support

, via email at

[email protected]

, or by phone at

(805) 933-9970

.

⚠

WARNING

Do not use the Cool Boss if the GFCI fails this test.

⚠

WARNING

Do not operate your Cooler if you find maintenance issues; instead, remove it from
service, then Assistance with your Evaporative Cooler is available from your dealer,

by calling Cool Boss at

(805) 933-9970

, or by emailing

[email protected]

. You may also contact Cool Boss for parts

replacement (please have the serial number and model number of your unit
available).

«
...
25
26
27
28
29
...
»

Summary of Contents for CB-12SL





































Reviews:

No comments