background image

Manual CC 5307 

5

 

ƒ

 

NOTICE 

 
 

Important Safeguard 

 

 

1. Read Instructions 

Read all of the safety and operating instructions before using the product. 

2. Retain Instructions 

Save these instructions for future reference. 

3. Attachments / Accessories 

Do not use attachments or accessories unless recommended by the appliance manufacturer as they 

may cause hazards, damage product and void warranty. 

4. Water and Moisture 

Do not use this product near water or moisture. 

5. Installation 

Do not place or mount this product in or on an unstable or improperly supported location. Improperly 
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only 

with a mounting device recommended by the manufacturer, or sold with the product. To insure proper 
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by 

manufacturer. 

6. Power source 

This product should be operated only from the type of power source indicated on the marking label.  

 

 

Precautions 

 

 

Operating 

-Before using, make sure power supply and others are properly connected. 
-While operating, if any abnormal condition or malfunction is observed, stop using the camera 

immediately and then contact your local dealer. 

 

Handling 

-Do not disassemble or tamper with parts inside the camera. 
-Do not drop or subject the camera to shock and vibration as this can damage camera. 

-Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your 
quality of camera. 

 

Installation and Storage 

-Do not install the camera in areas of extreme temperature, which exceed the allowable range. 

-Avoid installing in humid or dusty places. 
-Avoid installing in places where radiation is present. 

-Avoid installing in places where there are strong magnetic fields and electric signals. 
-Avoid installing in places where the camera would be subject to strong vibrations. 

-Never expose the camera to rain and water.  

 
 
 
 
 
 

 
 

 
 

 

Summary of Contents for CC-5307


























Reviews: