Control Microsystems SCADAPack LP Page 46 Hardware Manual Download

Page: 46 / 47

Transient
Protection

2.5kV surge withstand capability as per ANSI/IEEE
C37.90.1-1989

Isolation

Common ground return connected to Chassis Ground.

14.10 Digital

Inputs/Outputs

I/O points

8 points
Each point is an input and an output

Output Rating

1.0A maximum
0.35V maximum drop at 1.0A
0.05V maximum drop at 0.1A
Open drain sinking when ON.
28V maximum when OFF.

Input Rating

Dry contact input.
Wetting current typically 5mA, pulsed.
Contact closure to ground is ON.
Open input is OFF.

Digital Input
Thresholds

0.9V typical turn on input voltage.
Less than 0.4V guaranteed turn on input voltage.
1.5V typical turn off input voltage.
Greater than 2.2V guaranteed turn off input voltage.

Contact
Resistance

ON input requires less than 100

Ω

contact resistance.

OFF input requires greater than 50k

Ω

contact resistance.

Cable contact capacitance not to exceed 0.033uF,
typically 1600ft (500m).

Transient
Protection

2.5kV surge withstand capability as per ANSI/IEEE
C37.90.1-1989

Isolation

Common ground return connected to Chassis Ground.

SCADAPack LP Hardware Manual
May 26, 2006

Summary of Contents for SCADAPack LP
















































Search results

Summary of Contents for SCADAPack LP

Reviews:

Related manuals for SCADAPack LP

Brands by name

Popular brands

Control Microsystems SCADAPack LP, Hardware Manual

Search results

Summary of Contents for SCADAPack LP

Reviews:

Related manuals for SCADAPack LP

Brands by name

Popular brands