Optional Antenna Extension
In some installation scenarios, it may be desirable to enhance the Switch's wireless (RF)
transmission capabilities. This may be needed to overcome issues such as local
interference from other devices, range considerations due to the distance between devices
or the use of metallic faceplates. The Control4 Wireless Switch has been designed with a
wire whip antenna coiled underneath the plastic button that can be extended to
accommodate such scenarios. Instructions for extending the antenna are provided below.
WARNING!
To avoid risk of electrical shock that may cause personal injury or
damage to the Switch, this procedure should be performed prior to connecting the
switch at the wall box.
CAUTION!
Risk of Equipment Damage. This procedure enables advanced
functionality and should only be performed by a competent trained installer.
1
Remove the plastic button frame by squeezing
the side tabs near the top and bottom of the
button and pulling outward. A small flat-head
screw driver can also be used to assist in
releasing the tabs.
2
Once the button has been removed, detach the
radio board from its connector by gently pulling
away from the switch frame.
3
Slip the end of the antenna out of the radio
board hole and uncoil it, being careful not to
exert undue tension on the wire. Once uncoiled,
thread the antenna wire under the plastic spacer
at the bottom of the radio board.
4
Re-attach the radio card to the switch frame by
carefully aligning the connector and pressing gently. Then
re-attach the button and button frame by aligning the
button frame securement tabs with the appropriate slots on
the switch frame and pushing gently. Ensure that the
antenna is routed through the small notch on the bottom
left-hand side of the button frame provided for this
purpose. Once the button has been re-attached, proceed
with the standard installation procedure for wiring the
switch to the light load and securing it into the wall box, as
described in Step 1
5
The antenna has been designed to extend well beyond
the faceplate. For optimal performance, it should be
oriented in a vertical plane below the switch. To enable
this without leaving the antenna visible to the end user,
a very small hole should be made in the wall just below
the switch frame and the antenna inserted through the
hole back into the wall. Once the antenna has been
routed into the wall, proceed with standard installation
of the switch sub-plate and faceplate, as described in
Step 6
and Step 7
of “Installation Instructions.”
CAUTION!
Risk of Equipment Damage. The
antenna must not be inserted into the junction box containing high voltage wires.
IMPORTANT!
Do not shortened or cut the antenna in any way as this may
seriously impair transmission capabilities.
Troubleshooting
If light does not turn on:
•
Ensure at least one LED on the face of the switch is lit.
•
Ensure the light bulb is not burned out and is screwed in tightly.
•
Ensure circuit breaker is not turned OFF or tripped.
•
Check for proper wiring (see the “”section).
•
For help on the installation or operation of this product, email or call the Control4
Technical Support Center. Please provide your exact model number. Contact
[email protected] or see the web site www.control4.com.
Operation and Configuration
On initial power up, the unit
will flash the Red/Green/
Blue (RGB) LEDs, which
can be programmed with
different colors for different
states or color preferences.
To set up this switch for use
with a Control4 system,
refer to your system setup
documentation.
To operate this switch as a stand-alone device, refer to the following tables.
Limited 2 Year Warranty
Control4 Corporation ("Control4") warrants that at the time of first-consumer sale, this
product will be free from defects in material and manufacture. Control4 further warrants
that for a period of 2 years (24 months) after initial consumer sale, the product will function
in accordance with its specification, provided that it is installed and maintained under
normal and proper use. This warranty extends only to products purchased directly from
Control4 or an Authorized Control4 Reseller. If the product proves to be defective in
material or workmanship during the warranty period, it may be returned to the place of
purchase and Control4 will, at its sole option, repair or replace the product with a like
product. This warranty provides the consumer purchaser with specific legal rights, which
may vary per state or country. For complete warranty information, including details on
consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.
Regulatory Compliance
FCC
FCC ID: R33LSZ1011
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT!
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
ETL Statement
ETL Control Number: 3017581
This product has been tested by ETL and was found to comply with the Standard for Safety
for Industrial Control Equipment:
•
UL/ANSI Standard 508 (Seventeenth Edition)
•
CSA Standard C22.2 No. 14-05
Industry Canada
This Class B digital apparatus complies with Canada ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
About this Document
United States Patents Pending. Copyright © 2007 Control4 Corporation. Control4 and the
Control4 logo are registered trademarks of Control4 Corporation. All trademarks are
properties of their respective owners. Part Number: 200-00062 Rev A
Operate Switch
Expected behavior of RGB LEDs:
To operate switch:
Top
Bottom
Turn ON: Tap top.
Lit, full brightness
Not lit
Turn OFF: Tap bottom.
Not lit
Lit, full brightness
Care and Cleaning
Do NOT paint switch or its wall plate.
Do NOT use any chemical cleaners to clean the switch.
Clean surface with a soft damp cloth as needed.
