background image

Copyright 2021, Snap One, LLC. All rights reserved. Snap One and its respective logos are 
registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home 
Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My 
Home, SnapAV, Mockupancy, NEEO, OvrC, Wirepath, and Wirepath ONE are also registered 
trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the 
property of their respective owners. Snap One makes no claim that the information contained 
herein covers all installation scenarios and contingencies, or product use risks. Information 
within this specification subject to change without notice.

Troubleshooting

Reset to factory settings

Caution! 

The factory restore process will remove the Composer project.

To restore the controller to the factory default image:

Insert one end of a paper clip into the small hole on the back of the controller 
labeled 

RESET

.

Press and hold the 

RESET

 button. The controller resets and the 

ID

 button changes 

to solid red.

Hold the button until the 

ID

 flashes double orange. This should take five to seven 

seconds. The 

ID

 button flashes orange while the factory restore is running. When 

complete, the 

ID

 button turns off and the device power cycles one more time to 

complete the factory restore process.

Note: 

During the reset process, the 

ID

 button provides the same feedback as 

the Caution LED on the front of the controller.

Power cycle the controller

Press and hold the 

ID

 button for five seconds. The controller turns off and back on.

Reset the network settings

To reset the controller network settings to the default: 

Disconnect power to the controller.

While pressing and holding the 

ID

 button on the back of the controller, power on the 

controller.

Hold the 

ID

 button until 

ID 

button turns solid orange and the Link and Power LEDs 

are solid blue, and then immediately release the button.

Note: 

IDuring the reset process, the 

ID

 button provides the same feedback as 

the Caution LED on the front of the controller.

LED status information

 

 

 

       Just powered on

 

 

 

       Bootloader loaded

 

 

 

       Kernel loaded

 

 

 

       Network reset check

 

 

 

       Factory restore underway

 

 

 

       Factory restore fail

 

 

 

       Connected to Director

 

 

 

       Playing audio

—Flashing LED           —Solid LED

More help

For the latest version of this document and to view additional materials, open the URL 
below or scan the QR code on a device that can view PDFs.

Legal, Warranty, and Regulatory/Safety information

Visit 

snapone.com/legal

 for details.  

MOST RECENT VERSION

ctrl4.co/

core3-ig

MORE INFO ON CORE CONTROLLERS

ctrl4.co/

core

200-00725-A  

2021-10-21 DH

A

Connecting the contact port

The CORE-3 provides one contact port on the included pluggable terminal 
block (+12, SIG, GRD). See the examples below to learn how to connect various 
devices to the contact port.

Wire the contact to a sensor that also needs power (Motion sensor)

Wire the contact to a dry contact sensor (Door contact sensor)

Wire the contact to an externally powered sensor (Driveway sensor)

Connecting the relay port

The CORE-3 provides one relay port on the included pluggable terminal block. 
See the examples below to learn now to connect various devices to the relay 
port. 

Wire the relay to a single-relay device, normally open (Fireplace)

Wire the relay to a dual-relay device (Blinds)

Wire the relay with power from the contact, normally closed (Amplifier trigger)

Motion Sensor

+12V 0V COM NO

Dry Contact

Driveway

Sensor

External

12V Power

Fireplace

Dual-Relay Blind

UP

COM DOWN

Relay 1

Relay 2

12V Trigger

Activity

Caution

Link

Power

control4.com  |  888.400.4070

Summary of Contents for CORE-3












Reviews: