EMM-D4h
instruction manual
IM443-U v0.7
pag. 8
Programming
of
the
address
for
the
communication
network
(
SET
ID
ADR
)
(only
for
vers.
with
serial
output)
After the confirm with the
A
key of the previous value, the message
ID aDR
will appear
on
F
display; to set the value
that will identify the instrument when it will be connected in a EIA485 communication network, proceed with the
modality, already described. The settable values are from 1 to 247. To confirm, press the
A
key.
Programming of the baud rate (
SET BDR
) (only for vers. with serial output)
The
following
setting
is
the
baud
rate.
The
message
SET
appears
on
G
display,
the
message
SET BDR
on
the
first
two
parts
of
F
display
to
indicate
the
programming
of
the
baud
rate
displayed
on
the
third
part
(L3)
o
f
the
F
display.
To
modify
the
value
set,
it’s
necessary
to
use
the
C
key
to
decrease
and
B
to
increase
the
rate.
The
values
settable
are:
-
19.2
=> 19200
baud
-
9.60
=> 9600
baud
-
4.80
=> 4800
baud
-
2.40
=> 2400
baud
Press
A
to confirm the value displayed.
Programming of the serial parameters (only for vers. with serial output)
On
G
display will appear the message
SET
. The following message will appear on
F
display using the
B
and
C
keys.
To confirm press the
A
key.
8 1
8 data bit / 1 stop bit
PAR
No parity
NO
8 2
8 data bit / 2 stop bit
PAR
No parity
NO
8 1
8 data bit / 1 stop bit
PAR
Even parity
EVE
8 1
8 data bit / 1 stop bit
PAR
Odd parity
ODD
Programming of the Password (
SET PAS
)
The instrument is supplied without password. When a password (from 0002 to 9999) is set, using the
B
(to increase),
C
(to decrease) and
A
(to confirm) keys, only who know this value can to enter in the setup. The password, in fact, is
required all the time that someone try to enter in the setup (pressing the
A
and
B
key at the same time). If the
password is wrong, the message
PASS ERR
will appear on
F
display and the instrument go back to the measures
visualization. To input the password, when required by the instrument, at the enter of the setup, use the
A
,
B
and
C
keys as the same way done previously.
The menu is cyclic. After the last setting, the instrument go back to the first page of Setup (SETUP). It’s always
possible to come back to measures visualization mode pressing at the same time the
A
and
C
keys.
PEAK VALUES AND ENERGY COUNTERS RESET (
RESET
)
From the measures visualization mode, pressing the
A
and
C
keys simultaneously the message
SETUP
will appear
on
F
display, press the key
C
until the message
RESET
appears on the same display. To accede to the menu, press
the
A
key. Now it’s possible to select the enabling of cancellation type, by pressing the
C
key, according with following
types:
RESET PEA
: all maximum value will be delete.
RESET AVG
: all average and average maximum value (maximum demand) will be delete.
RESET EN
: with
NORMAL
as energy mode (
EN
) the total energy counters will be delete, with
TOT PAR
the
partial energy counters will be delete (as when the digital input is closed) and with
TB1 TB2
the band
counters will be delete.
RESET ALL
: to delete average maximum values and energy counters.
Entry to menu:
seT UP
seT Up
RESET
SET DO1
SET DO2
SET AN OUT
SET HR_
--- OFF OFF
(the visualization depends on the settings and the I/O status)
RESET PEA
NO
/
YES
Confirm Reset
Deleting maximum values (max)
RESET AVG
NO
/
YES
Confirm Reset
Deleting average values (avg)
and maximum demand (maxD)
RESET EN
NO
/
YES
Confirm Reset
Deleting energy counters
RESET ALL
NO
/
YES
Confirm Reset
Deleting maximum and average
values, and energy counters
To enable the chosen type, press the
B
key to change the indication on display
G
from
NO
to
yes
.
Confirm enabling cancellation, by pressing the
A
key. The indication on display
G
change from
yes
to
---
.
