background image

SECTION 3: INSTALLATION

3

•  All pedicure chairs MUST be installed by a licensed electrician and a licensed plumber in 

accordance with all national, state, and local codes/regulations. 

•  Failure to comply with these codes and/or regulations will result in the limited warranty 

being null and void. 

•  Your  chair  will  not  operate  properly  unless  it  has  sufficient  water  pressure  and 

temperature, proper drainage and adequate electrical power.

•  ANY INSPECTIONS OR APPROVALS ARE THE SOLE RESPONSIBILITY OF THE PURCHASER. 

PRIOR TO INSTALLATION, ONE SHOULD CONTACT THEIR LOCAL BUILDING INSPECTOR TO 

MAKE SURE ALL LOCAL CODES ARE COMPLIED WITH.

•  IMPORTANT: Client’s ventilation intake needs to pull a minimum 80 CFM at the chair’s 

connection point to achieve 50 CFM from open vent.

In order to ensure access after installation, please refer to installation drawings available at 

MyContinuumPedicure.com

Install to Permit Access for Servicing

EXTREMELY IMPORTANT: Each pedicure chair MUST be anchored to the floor. This is especially 

critical if pedicure chair is gravity drained with or without air gap. There are two (2) black 

mounting brackets supplied with each pedicure chair for this purpose. Your warranty is null 

and void if pedicure chair is not properly secured to finished floor.
•  Location & Support: 
The floor structure must be level and capable of supporting the 

occupied pedicure chair. Refer to installation drawings at MyContinuumPedicure.com

•  DEPENDING ON THE USE OF MANICURE TRAYS AND/OR CARTS, THE EXACT DISTANCE 

BETWEEN PEDICURE CHAIRS WILL VARY GREATLY. THIS MUST BE DISCUSSED PRIOR 

TO ORDERING PEDICURE CHAIRS. THIS WILL ENSURE PROPER INSTALLATION AND 

ADEQUATE WORKING SPACE. Please contact Continuum Footspas if additional 

information is required.

• 

When determining distance between back edge of unit and finished wall, it should 

be noted chair does recline. To ensure chair does not touch back wall, please review 

“Installation Drawings” for suggested minimum clearances.

Step 1: Utilizing a level, carefully adjust the six (6) leveling feet. It is extremely important 

that your pedicure chair is level. (Note: All leveling feet have been factory adjusted prior to 

shipment. In most cases no further adjustment should be necessary). The entire pedicure chair 

may be raised or lowered slightly to ensure the technicianʼs chair touches the front stainless 

steel guard and not the wood or Formica®.
Step 2: Mounting brackets are to be used on only two (2) of the four (4) main frame leveling 

feet. Slotted portion of the mounting bracket fits between frame and the leveling foot (one in 

front, one in back, opposite of each other). The flat portion with holes should be positioned to 

the floor. Use appropriate hardware to secure to the floor (not supplied).

Installation Instructions

Important Installation Notes

Summary of Contents for Maestro Opus









Reviews: