Contemporary Controls CTRLink EISC-100T Installation Manual Download Page 1

 

 

EISC-100T

 

Ethernet Configurable Switching Hub 

 

INSTALLATION GUIDE 

Introduction 

The  EISC-100T  (EISC)  configurable  switch  in  the  CTRLink

®

  family 

provides  capabilities  beyond  those  of  standard  Plug  and  Play  (PnP) 
switches.    Besides  conventional  features  —  auto-negotiation,  10/100 
Mbps data rate, flow control, half- or full-duplex operation — the EISC 
has advanced features such as VLAN, trunking, Quality of Service (QoS) 
and  a  programmable  fault  relay  that  can  be  connected  to  a  supervisory 
system.    Individual  port  parameters  can  be  configured  via  a  console  port 
attached  to  a  Windows

®

-based  workstation.    Port  status  can  also  be 

monitored through the console port using the Modbus protocol, making it 
easy  to  interface  the  EISC  with  supervisory  control  equipment.    These 
features  make  the  EISC  one  of  the  most  versatile  of  Industrial  Ethernet 
switches available. 

Configuration  is  accomplished  via  a  console  port  connected  to  a 
Windows-based  configuration  program  included  with  the  product.  
Modbus protocol and register information is also provided so the switch 
can be configured or monitored by a Modbus master device.  Each port 
parameter  (data  rate,  duplex  and  flow  control)  can  be  pre-set  via  the 
console port or set automatically via auto-negotiation.  And a unique feature 
displays the status (integrity) of the cable attached to any each port. 

Each port automatically optimizes its data rate to 10 Mbps or 100 Mbps 
— but data rate and duplex settings can be specified, if desired. 

Each  port  negotiates  flow  control,  but  control  can  be  disabled  for 
individual ports.  The PAUSE function is supported for full-duplex links.  
The backpressure scheme is used for half-duplex segments. 

The EISC can be powered from wide-range, low-voltage 
AC or DC sources and has provisions for either DIN-rail 
or panel mounting. 

Summary of Contents for CTRLink EISC-100T









Reviews: