FXR2000-G Setup Guide
Connecting to This Product Using Web Browser
Start a Web browser and enter the IP address of this product after
“http : //” in the address bar.
If connecting for the first time, enter the default IP address.
http : //192.168.0.1/
Connected to this product, the login screen is displayed. The
default username and password are:
Username: admin
Password: pass.
Setup Using Web Browser
Select the desired setting items from the opened menu (1).
Information such as setting items will be displayed in the
right-hand frame.
For more information about a setting item, please refer to “help”
(2).
Click “Submit” (3) after changing settings on each page to
temporarily save the settings in this product.
The settings become enabled when the product is restarted after
all the setup procedure is completed and the settings are stored.
Click “Save & Reboot” (4) on the left-hand menu.
Firmware Update
To update FXR2000 firmware, select “Maintenance” >
“Firmware” (1).
“Browse...” (2) to the firmware file (extension .bin) and then click
“Update” (3).
If Firmware was updated, the page will look like this:
The update become enabled when the product is restarted.
Click “Reboot” (4) on the left-hand menu..
Serial port Setting
Use these parameters to configure the serial port on the FXR2000-G to match the settings on the connected serial device.
1.
Data bits: Number of data bits. (Default=8bit)
2.
Parity bit: Sets the parity. (Default=None)
3.
Stop bits: Number of stop bits. (Default=1bit)
4.
Baud rate: Baud rate in bps. (Default=38400)
5.
Software flow control: (Default=None)
None: Flow control is none.
XON/XOFF: Flow control is performed locally using XON/XOFF. In this case, the attached serial device must
also support software flow control.
6.
Hardware flow control: (Default=None)
None: Flow control is none.
RTS/CTS: Flow control is performed locally using RTS (Request To Send)/CTS (Clear To Send). In this case, the
attached serial device must also support hardware flow control.
7.
Max receive buffer: Receive buffer size in bytes. If the buffer becomes full, data is discarded until space can be
freed up. (Default=1024byte)
Factory Reset
There are two ways to restore Default Settings
- Using a web browser
- Using the DIP switch of the main unit (INIT)
Each Default method is as follows.
Using a Web Browser
(1)
Use a web browser to log in to this product.
(2)
Select “Maintenance” - “Default setting” from the menu.
(3)
Two Options: 1st option – Restore Default settings but keep the current IP address – check “IP address is NOT
made a default.”
2nd option – Restore Default settings and reset IP address to 192.168.0.1 - check “IP address is made a default.”
Choose either option and then click “Default”.
(4)
Click “Save/Reboot” on the menu to save the default setting to reboot the product.
Saving the setting and rebooting the product in the step (4) initializes the product.
Using the DIP Switch (INIT)
(1)
Turn on switch 1 of the DIP switches (left switch, INIT) at the front part of the main unit.
(2)
Immediately after that, the POWER LED, WLAN, COM LEDs flash for approximately three seconds. Turn off
DIP switch 1 during the flashing.
(3)
Wait until the flashing stops, then reboot the unit.
The POWER LED, WLAN, COM LEDs continue to flash for a little while after DIP switch 1 is turned off. Turning off the product
during flashing may damage the file in the memory and cause improper operation of the product. Reboot the product after the flashing
stops.
DIP Switch default setting
SW 1
2
O
N
Switch 1: OFF
Switch 2: OFF
Specifications
Item
Specification
Wired LAN
Ethernet standard
IEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX)
Data transfer speed
10 / 100Mbps
Access method
CSMA/CD
Communication type
Half Duplex, Full Duplex
Number of ports
1 (10BASE-T / 100BASE-TX)
Wireless LAN
Wireless LAN standard
IEEE802.11n, IEEE802.11a, IEEE802.11b, IEEE802.11g
IEEE802.11n
Channel USA
(FCC)
5GHz 24h(36, 40, 44, 48ch[W52], 52, 56, 60, 64ch [W53], 100, 104, 108, 112, 116, 132,
136, 140ch [W56] 149, 153, 157, 161, 165ch [W58] )
2.4GHz 11ch (1 - 11)
Data transfer speed *1
300 - 6.5Mbps[MSC0 - 15, Short/Long GI] (Fixed / Auto)
IEEE802.11a
Channel
USA(FCC)
24h(36, 40, 44, 48ch[W52], 52, 56, 60, 64ch [W53], 100, 104, 108, 112, 116, 132,
136, 140ch [W56] 149, 153, 157, 161, 165ch [W58] )
Data transfer speed *1
54, 48, 36, 24, 18, 12, 9, 6Mbps (Fixed / Auto)
IEEE802.11b
Channel
USA(FCC)
11ch (1 - 11)
Data transfer speed *1
11, 5.5, 2, 1Mbps (Fixed / Auto)
IEEE802.11g
Channel
USA(FCC)
11ch (1 - 11)
Data transfer speed *1
54, 48, 36, 24, 18, 12, 9, 6Mbps (Fixed / Auto)
Security
IEEE802.11n
WPA(AES), WPA2(AES), WPA-PSK(AES), WPA2-PSK(AES),
WSL(combination mentioned above are possible)
IEEE802.11a/b/g
WEP(open/ Shared Key /Auto), WPA(AES, TKIP), WPA-PSK(AES,TKIP),
WPA2(AES, TKIP), WPA2-PSK(AES,TKIP), IEEE802.1X(EAP-TLS, PEAP),
WSL(combination mentioned above are possible)
Serial
unit
Serial standard
RS-232C
Data transmission
speed
300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200bps
Number of channels 1
Connector
9 pin D-SUB, F (Female) type
Antenna connector
R-SMA Connector x2
External Dimensions (mm)
38(W) x 135(D) x 124(H)
(Not including antenna connector and other projecting parts)
Weight (kg)
0.5
*1 These are theoretical values based on their respective wireless LAN standards. They do not indicate actual data transfer rates.
Environmental Specifications
Item
Specification
Input voltage range
5 – 30VDC±5%
Rating input current
1.4 – 0.24A
Operating ambient temperature
0 - 50
°
C
Operating ambient humidity
10 - 90%RH (No condensation)
Floating dust particles
Tolerant of small amounts (non excessive)
Corrosive gases
None
External Dimensions
5-30VDC
2
SW
ON
1
LAN
COM WLAN
13
5
124
38
51
61
96
ANT 1
ANT 2
[mm]
Image of installation
5
-3
0
V
D
C
2
S
W
L
A
N
C
O
M
W
L
A
N
A
N
T
1
A
N
T
2
1
FXR2000-G
2