background image

1. Before Using the Product

                                                                                                                                                

 

6

FA-UNIT-F6BE/2U

Environment

Use this product in the following environment.    If used in an unauthorized environment, the board may

overheat, malfunction, or cause a failure.

Operating temperature

0 - 50

°

C

Operating humidity

10 - 80%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically as follows to use it safely.

- Ventilating slits must neither be blocked nor have

   dust or foreign matters adhering.

- Ventilating slits must neither be blocked

  nor have dust or foreign matters adhering.

Front side view

Rear side view

Side view

Storage

When storing this product, keep it in its original packing form.

(1) Put this product in the storage bag.

(2) Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

Summary of Contents for FA-UNIT-F6BE/2U





























Reviews: