manualshive.com logo in svg

Contec COM-4CN-USB, User Manual, Page: 17 / 41

Share
Download
Contec COM-4CN-USB User Manual Download Page 17

2. Setup 

 

 

 

12

 

COM-4CN-USB 

Component Functions 

LED indecator 

 

LED 

Meaning 

Status 

POWER (Green)  Power status 

OFF: Power has not been supplied. 
ON: Power has been supplied. 

RxD (Yellow) 

Reception status 

OFF: It indicates receiving data by the RS-
232C in standby 
ON: It indicates receiving data by the RS-
232C. 

TxD (Green) 

Transmission status 

OFF: It indicates sending by the RS-232C in 
standby. 
ON: It indicates sending data by the RS-
232C. 

 

 

Connecting the Product 

(1)  Turn on the power to the PC before connecting this product. 

(2)  Sandwich the supplied USB cable with the USB cable attachment and connect to the product. This 

makes the cable hard to disconnect. 

 

Figure 2.2. Connecting the Product 

 

 

 

- 

The USB cable attachment cannot be used excluding an attached cable. 

- 

When the USB cable attachment is being used, do not perform removing and connecting the USB 
cable on the product side repeatedly. This may damage the USB cable attachment or yourself. 

 

CAUTION

Summary of Contents for COM-4CN-USB










































Reviews:

No comments