Removing existing CPU cooler
1.
Ground yourself with a grounding mat or anti-static wristbands to prevent electrical static discharge (ESD)
from your body and clothes during installation. Integrated circuits are sensitive to electrical static. They
can be damaged or destroyed if ESD occurred.
2.
Open the computer housing, remove the motherboard and extract the old CPU cooler carefully.
3.
Remove any remaining heat-conductive paste or heat-conductive foil completely from the surface of the
CPU. For this, use a soft object only and be very cautious as otherwise the CPU may be permanently
damaged!
New Installation
1.
When assembling a new computer, put the lever of the ZIF socket into the vertical position, insert the CPU
correctly (and carefully) and close the ZIF socket again.
2.
Position the motherboard on a smooth, flat service. To protect the surface (e.g. writing-desk), insert a
piece of cardboard between the motherboard and surface.
3.
Don’t touch the grey heat-conductive past on the underside of the cooler, because otherwise parts of
the CPU surface will not obtain heat-conductive contact. This would pose a risk of overheating and
destruction of the CPU as well as the loss of guarantee/warranty!
4.
Adjust the mounting holes of the backplate to fit your motherboard type.
5.
Adjust the position of the spring screw so that the CPU cooler can be placed in the correct position on the
CPU. Fasten the cooler with the spring screws.
Completion
1.
Connect the 4-pin plug to the CPU fan connection on the motherboard. For the exact position of the
connection, please refer to the operating instructions for the motherboard. The connection may be
labelled “CPUFAN1” or similar.
2.
Secure all cables by means of one or several cable ties so that they cannot become entangled in one
of the computer’s fans.
3.
Install the motherboard in the computer housing. Do not hold the motherboard by the CPU cooler.
4.
Close the computer housing again and connect the computer to the mains supply.
Please visit the website of the manufacturer,
www.akasa.com.tw
for update or further
information.
Tips and hints
•
If you do not possess expertise for installing this cooler, leave the task of assembly to a trained technician,
or technical workshop. This will be cheaper than damaged or destroyed components of your motherboard!
•
If the cooler may have to be removed at any point, heat sink and chip must be properly cleansed of all
residual heat-conductive paste before reinstallation.
•
Due to the electric conductivity of special heat-conductive pastes, the motherboard could be short-circuited
if any of the paste were to come into contact with the motherboard, or the contacts of sockets! Respective
components may be destroyed!
•
The heat-conductive thermal compound paste is only suitable for single usage! To remount the cooler
again, please use a suitable heat-conductive paste and apply it to the topside of the chip (a layer of approx.
0.1 – 0.2 mm thickness is sufficient).
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Type of socket
......................................
Intel LGA 775, 1156
Air flow
..................................................
55.4 CFM
Ventilator speed
....................................
600 - 3000 rpm
Noise level
............................................
17.7 to 28.8 dB(A)
Dimensions (W x H x D)
.......................
95 x 95 x 63 mm
Weight
.................................................. 395 g
Operating instructions
Akasa CPU Cooler Intel LGA 775 & LGA 1156
Item no. 974991
Intended use
The product is used for cooling the CPU on the mainboard of a computer. Operating heat is dissipated via
a cooling element which is air-cooled by a high-performance fan. The product is designed for cooling Intel
processors (LGA 775 / 1156).
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuits or fire. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Content of delivery
•
CPU cooler
•
Intel backplate (LGA 775 / 1156)
•
Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code above.
Follow the instructions on the website.
Sicherheitshinweise
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
•
The product is not a toy and should be kept out of reach of children!
•
Do not leave packaging material lying scattered about unattended. It might become dangerous
toys for children.
•
If the heat-conductive paste come into contact with skin, wipe it off with a dry cloth and then
clean the area thoroughly with warm water and soap. In case the heat-conductive paste
contacts with the eye, flood the affected eye immediately with warm water. Then consult a
doctor immediately.
•
When used in conjunction with other devices, observe the operating instructions and safety
notices of connected devices.
•
The product must not be subjected to heavy mechanical stress.
•
The product must not be exposed it to extreme temperatures, direct sunlight, intense vibration,
or dampness.
•
The thermal paste should be kept away from electrical traces, pins, and leads.
•
When replacing cooling element, do not use the old thermal paste/ pad. Remove all remnants
of the old thermal paste/ pad. Apply new thermal paste/ pad before reinstalling another cooling
element.
•
Only a thin and evenly distributed layer of thermal paste should be placed between the
processor and the cooler.
•
Never place any object between the processor and the cooler! Due to the greater displacement
in between will decrease cooling effect; the processor will overheat and be permanently
damaged.
•
In industrial facilities, the safety regulations laid down by the professional trade association for
electrical equipment and facilities must be adhered to.
•
When in doubt about how to install the device correctly, please contact an expert or a specialist
workshop and let them carry out the installation.
•
Servicing, adjustment or repair works must only be carried out by a specialist/ specialist
workshop.
•
If any questions arise that are not answered in this operating instruction, contact our Technical
Advisory Service or other experts.
•
Be sure to observe the following safety notes regarding the heat-conductive paste, according
to REGULATION (EC) No 1272/2008:
-
H410:
Warning!
Very toxic to aquatic life with long lasting effects.
-
P273:
Prevention:
Avoid release to the environment.
-
P391:
Response:
Collect spillage.
Installation
Before installing the CPU cooling element, make sure to turn off the computer, switch off the
main switch on the back of the power supply unit and unplug the mains plug. Since voltage is
present even when the computer is switched off, there is a risk of electric shock when touching
electric components inside.
Installation slightly differs depending on whether the fan is installed to replace an existing „old“ fan, or if you
want to assemble a new computer.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*974991_v4_0217_02_jh_m_en
