These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
V3_0713_02-HK
Initial operation
1. Place the shredder on a level surface.
2. Plug the mains plug into a mains socket.
a) Shredding paper
Do not insert more than 6 sheets of paper (size DIN A4 with a maximum grammage of
75 g/m2) into the insertion slot.
Do not shred adhesive notes or paper with remains of adhesive.
1. Slide the selector switch to the right into the ‘AUTO’ position.
2. Now, carefully insert the paper into the insertion slot. The paper will automatically be fed in and shredded.
b) Shredding CDs / credit cards
Shred only one CD or credit card at a time.
1. Place the small collection container in the guide rails under the CD/credit card insertion slot.
2. Slide the selection switch into the middle position, ‘FWD CD/Card’. The motor is now permanently turned on.
3. Next, carefully insert a single credit card into the credit card insertion slot. The credit card will be fed in
and shredded.
4. Bring the grey cap into the upright position to shred a CD.
5. Next, carefully insert a single CD into the CD insertion slot. The CD will be fed in and shredded.
6. When finished, slide the selector switch to the right, into the ‘AUTO’ position.
c) Clearing paper jam
1. Slide the selector switch to the ‘REV’ position.
2. The cutting unit will now run in the reverse direction and push the jammed paper out again.
3. If pieces of paper remain in the cutting unit, press and hold the ’CLEAR’ button. The remaining pieces
will now be shredded.
Troubleshooting
Problem
Solution
The cutting unit continuously keeps on
running in the ’AUTO’ position.
The paper container is full and the paper from the cutting unit
cannot feed through.
• Unplug the mains plug and empty the container.
After shredding, there are still pieces of
paper remaining in the cutting unit.
The remaining pieces of paper are stuck between blades.
• Slide the selector switch into the ‘REV’ position or press and
hold the ‘CLEAR’ button.
The automatic paper feed does not
work properly after having used the
cutting unit’s ‘REV’ mode.
Remaining pieces of paper block the automatic feed.
• Slide the selector switch into the ‘REV’ position or press and
hold the ‘CLEAR’ button.
The automatic feed stops, however
there is still paper in the insertion slot.
The paper was inserted into the insertion slot at an angle.
• Ensure the paper is straight as it goes into the insertion slot.
The paper is too soft, thin, damp or creased.
• Fold, dry or flatten the paper.
The device does not work, although no
pieces of paper remain in the feeder.
The motor is overheated.
• Leave the device to cool down before putting it into
operation again.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ........................................ 230 V/AC, 50 Hz
Max. power consumption ............................. 0.9 A
Safety level .................................................. 2 (acc. to DIN 32757)
Noise level ................................................... < 72 dB
Shredding speed ......................................... 7 seconds per DIN A4 page
Container volume ........................................ 10 l (paper)
0.75
l
(CD/credit
card)
Operating temperature ................................ -10 ºC to +85 ºC
Blade clearance ........................................... 7 mm (paper)
40
mm
(CD/credit
card)
Insertion slot width ....................................... 220 mm
Dimensions (W x H x D) .............................. 280 x 286 x 146 mm
Weight ......................................................... 1.5 kg
Document Shredder IPS018.s
Version 07/13
Item no. 88 34 82
Intended use
This product is designed for shredding paper, CDs and credit cards. The separate collection container allows
the separation of shredded CDs and credit cards from shredded paper. Use the product only in dry indoors.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Shredder
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• Do not reach into the feeder slot.
• Do not insert paper pin, staples or any other metal parts into the feeder slot.
• Keep long hair away from around the feeder slot.
• Keep ties, scarves, loose clothing and long necklaces or bracelets away from the feeder slot.
• Do not use spray bottles / cans in the immediate vicinity of the product.
• The product must not be exposed it to extreme temperatures, direct sunlight, intense vibration,
or dampness.
• Unplug the mains plug from the mains outlet before cleaning the product or storing it for a
longer period.
• Do not operate the device for longer than 2 minutes to avoid overheating the motor.
• The product should not be connected immediately after it has been brought from an area of
cold temperature to an area of warm temperature. Condensed water might destroy the product.
Wait until the product stabilising to adapt to the new ambient temperature before use.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating elements
1 Selector switch
2 ’CLEAR’ button
3 Credit card insertion slot
4 CD insertion slot
5 Paper insertion slot
6 Collection container