These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
V1_0114_02-ETS-Mkde
Operating elements
1
2
3
4
5
6
7
1 Support arm
2 Set screw
3 Suction cup
4 Suction cup tongue
5 Locking lever
6 Set screw
7 Holding bracket
Operation
Choose an installation surface that will not impair your visibility of the road
or cause distraction during driving.
Heed all legal restrictions concerning the use of mobile telephones in
vehicles.
1. Make sure that the suction cup (3) and the installation surface are clean, dry and free from
grease and dust.
2. Connect the holding bracket (7) to the support arm (1). The holding bracket must click into
place audibly.
3. Hold the suction cup to the installation surface and apply a little pressure.
4. Push the locking lever (5) toward the installation surface so that the suction cup adheres to
the surface. Make sure that the suction cup is well fastened.
5. Place your iPhone in the holding bracket. The two rounded corners of the holding bracket
should be on the left side of the iPhone to prevent covering the camera on the back. The
iPhone must click into place audibly.
6. Loosen both set screws (2 + 6) and position the iPhone according to your individual needs.
Then refasten both set screws.
7. To remove the suction cup from the installation surface, first lift the locking lever and then
pull the suction cup tongue (4) away from the installation surface.
Maintenance and cleaning
Never use any aggressive cleaning agents or chemical solutions.
• Use a slightly damp cloth to clean the suction cup. Use a mild cleaning agent to clean off
tougher dirt. Allow the suction cup to fully dry before returning it to the installation surface.
• Use a dry, soft and clean cloth to clean the plastic components. You can use a long-haired,
soft and clean brush and a vacuum cleaner to remove dust.
Disposal
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
Suitable for .................................................. Apple iPhone 5 / 5c / 5s
Operating conditions .................................... 0 to +40 ºC, 45 – 80 % RH (non-condensing)
Storage conditions ....................................... -20 to +60 ºC, 30 – 90 % RH (non-condensing)
Suction cup Ø .............................................. 78 mm
Holding bracket dimensions (W x H) ........... 56 x 125 mm
Weight ......................................................... 99 g
Car holder for iPhone 5 / 5c / 5s
Version 01/14
Item no. 759912
Intended use
Use this product to fasten an Apple iPhone (5 / 5c / 5s) to the windshield inside a car. The
suction cup guarantees secure fastening. The product has two joints that can be used to
position the iPhone according to your individual needs.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Car holder
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
