Alarm Floor Mat
Version 04/11
Item no. 75 19 13 (type „Large“)
Item no. 75 18 62 (type „Small“)
Intended Use
The product is intended for connection to a suitable alarm system, where it is used for the
surveillance of entrance areas.
The alarm floor mat is placed, for example, under carpets or doormats; when the alarm
floor mat is stepped on the integrated NO contact will be closed and thus, the alarm sys-
tem will be triggered.
The alarm floor mat also features an integrated tamper switch (NC contact); when the
cables are cut, the alarm system can even so activate the alarm.
This product complies with the applicable National and European requirements. All names
of companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• Alarm floor mat
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions! We do not assume any liability for any
consequential damage!
Nor do we assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! The war-
ranty will be void in such cases.
• The unauthorized conversion and/or modification of the product is not allowed because
of safety reasons. Never disassemble the product.
• The product is not a toy and should be kept out of the reach of children.
• The product should only be used in dry indoor areas, it must not become damp or wet.
Never operate it in or under water.
• Do not drive on the alarm floor mat with vehicles, as it may be damaged.
• Do not leave packing materials unattended. They may become dangerous playthings for
children.
• Handle the product with care; sharp objects may damage the product.
Connection
1 Alarm contact (normally open contact, NO)
2 Tamper switch (normally closed contact, NC)
3 Pressure-resistant edge for attachment
The alarm floor mat is hidden, e.g. behind a door under the carpet or a floor mat. The alarm
floor mat consists of two electro conductive layers, which function as a closure contact under
mechanical load (also known as „NOC“ (normally open contact)). The connection to an
appropriate alarm loop of the alarm system is made via the two cables (1).
A tamper switch is built-in as protection against tampering. It functions as a break contact
(also known as „NC“ (normally closed) contact). Connect this to the alarm system as well,
pay attention to the alarm system’s operating instructions.
☞
The connections to the alarm floor mat are made with suitable cables, take care
not to cause any short-circuits (false alarm), e.g. use shrink tubing.
The alarm floor mat is usually fixed in place with adhesive tape; the outer edge (3) of the
alarm floor mat is suitable for this purpose.
You may also use double-sided adhesive tape to attach the alarm floor mat to the floor.
O P E R A T I N G I N S T R U C T I O N S
www.conrad.com
☞
Make sure the alarm floor mat does not become damaged while attaching it to
the floor (e.g. protruding nails/screws, small stones or dirt).
The alarm floor mat must be laid out flat on the floor. Declivities, corner battens
or tile joins may lead to malfunctions. Moreover, the carpet or the floor mat that
is placed over the alarm floor mat, should not be too heavy.
Place the alarm floor mat where it cannot get damp or wet. Pay attention so
that neither the alarm floor mat nor the connection cables are visible.
Switch on your alarm system after installation and check the functioning of the alarm floor
mat by stepping on it.
If the alarm is not activated, check that the connection is correct (NC or NO contact inter-
changed or similar).
Disposal
Please dispose of the device, when it is no longer of use, according to the current
statutory requirements.
Technical Data
Dimensions: ..............................Approx. 710 x 405 x 6mm (Item no. 751913)
Approx. 590 x 190 x 6mm (Item no. 751862)
Contact load capacity ................Max. 30V, 0.1A
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.
3
2
1
