b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating elements
1
2
4
10
5
6 8
9
7
3
1 Adapter 1 (“SENDER” imprint) to connect to the computer
2 RJ45 socket, connect to the RJ45 socket (5) via a 1:1 connected and fully wired patch cable
3 USB plug, connect to a free USB port of your computer
4 Adapter 2 (“RECEIVER” imprint) to connect the USB device
5 RJ45 socket, connect to the RJ45 socket (2) via a 1:1 connected and fully wired patch cable
6 Green LED, indicates a data transfer (flashes)
7 Yellow LED, indicates a connection (link LED)
8 Red power LED
9 USB socket, connect the USB device here
10 Low voltage socket, connect the plug-in power adapter provided here
The function of the 3 LEDs (6, 7, 8) is the same on both adapters.
Operation
1. Connect the USB plug (3) to a free USB port of your computer. The red power LED (8) on the adapter (1)
lights up. Windows
®
recognizes the new hardware.
2. Connect the round low voltage plug of the plug-in power adapter provided to the low voltage socket (10).
The red power LED on the adapter lights up.
3. Finally connect both RJ45 sockets (2 and 5) via an 8-pole, fully wired, 1:1 connected patch cable. After a
short time the link LED (7) lights up on both adapters. In addition the data transfer LED (6) starts to flash.
Do not use any cross link cable and also no partially wired RJ45 cable, otherwise no function
is possible.
4. Connect the USB plug of your USB device to the USB socket (9).
5. Windows
®
should recognize the new hardware depending on the USB device connected (e.g. if the USB
device has not been operated on the computer yet). Subsequently the USB device is available, as if it
was directly connected to the computer.
6. The data transmission LED (6) on the adapters flashes when transferring data (e.g. of a USB stick).
Only one single USB device can be connected. It is not possible to operate a USB hub with
several devices.
If you do not have any access to the USB device, check whether the firewall of your operating
system denies access. Then approve access via the firewall.
Tips & notes
• The maximum possible speed for transferring data via the patch cable depends on the USB device, the
PC and the cable length.
• A maximum of 7-8 MByte/s are effectively attainable (e.g. with a USB hard drive or a fast USB stick)
• Both RJ45 sockets of both adapters should be directly connected via a 1:1 connected patch cable. It is not
possible to operate a network switch or any similar device in between.
• Due to the large number of USB devices and their functions it is possible, that some devices cannot be
operated via the USB extension.
• It may also be the case, that not every single function is supported (e.g. ink level display of a printer or
similar).
USB 2.0 Extension via
patch cable, 100 m
Version 01/15
Item no. 1278722
Intended use
The product establishes a USB connection via a patch cable up to 100 m in length. Therefore USB devices
can also be operated at a great distance from the computer. The plug-in power adapter provided supplies
power to the USB device.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. In addition, improper
use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Adapter 1 (“SENDER” imprint) to connect to the computer
• Adapter 2 (“RECEIVER” imprint) to connect the USB device
• Plug-in power adapter
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous
playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from
any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
• Make sure that the insulation of the entire product is not damaged or destroyed.
• Never pour any liquids over electrical devices or put objects filled with liquid right next to the
device. If liquid or an object enters the interior of the device nevertheless, first power down the
respective socket (e.g. switch off circuit breaker) and then pull the mains plug from the mains
socket. Do not operate the product anymore afterwards, but take it to a specialist workshop.
• Never use the product immediately after it has been brought from a cold room into a warm one.
The condensation generated could destroy the product. The power supply unit also involves
danger to life by electric shock! Allow the device to reach room temperature before connecting
and using it. This may take several hours.
• The adapter corresponds to protection class II. Only a proper mains socket (230 V/AC, 50 Hz)
of the public supply net must be used as voltage source.
• If the power adapter is visibly damaged, do not touch it. Risk of fatal injury due to electric shock!
First turn off the power supply to the power outlet that the power adapter is connected to (flip
off the fuse and then turn off the residual current operated circuit breaker to disconnect the
power outlet at all phases). Now unplug the device from the power outlet. Dispose of the power
adapter in an environmentally friendly fashion, discontinue use of it immediately. Replace it with
an identical power adapter.
• The power socket into which the device is inserted must be easily accessible.
• Only use the supplied mains adapter as a power supply.
• Only connect the power adapter to a normal mains socket connected to the public supply.
Before plugging in the power adapter, check whether the voltage stated on the power adapter
complies with the voltage of your electricity supplier.
• Never connect or disconnect power adapters if your hands are wet.
• Never unplug the power adapter from the mains socket by pulling on the cable; always use
the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or damaged by
sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
• For safety reasons, disconnect the power adapter from the mains socket during storms.
