ConnectedIO ER1000-VZ User Manual Download Page 18 | Manualshive

Page: 18 / 21

background image

Figure 20: Kernel Log

7. Antenna

7.1.

Antenna – Installation Guidelines

When installing the antenna to the ER1000 product line there are a number
of items to consider so good antenna performance can be maintained.



Install the antenna in a place covered by the LTE signal.



Antenna must not be installed inside a metal case.



Antenna shall also be installed according to the Antenna manufacturer
instructions.



Antenna integration should optimize the Radiation Efficiency.
Efficiency values >50% are recommended on all frequency bands for
any antennas selected.



Antenna integration should not dramatically perturb the radiation
pattern. It is preferable to get, after antenna installation, an
omnidirectional radiation pattern for the best overall coverage.



Antenna Gain must not exceed values indicated in the regulatory

«
...
16
17
18
19
20
...
»

Summary of Contents for ER1000-VZ






















Reviews:

No comments

Related manuals for ER1000-VZ

Brand: D-Link Pages: 267

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Cambium Networks Pages: 29

Brand: Campbell Pages: 42

Brand: LaCie Pages: 22

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

RP614 - Web Safe Router

Brand: NETGEAR Pages: 16

Brand: Patton electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands