manualshive.com logo in svg

Connect Tech PCI-104, User Manual

Share
Download
Connect Tech PCI-104 User Manual Download Page 28

Connect Tech Xtreme/104-Plus, PCI-104 and PCI/104 Express Family User Manual 

                                                                                                                         Revision 0.09 

28 

 

For 2-wire networks only the Jx.2A/Jx.2B jumpers should be installed. The 

Jx.1E/Jx.1F jumpers are not used and will have no effect. 

 

 

17.5  Line Interface Mode Jumpers for Xtreme/PCI-104 Opto 12 Port 

 

The Line Interface Mode Jumpers function is as follows: 
 

Mode / Jumpers 

Jx..1A 

Jx..1B 

Jx..1C 

Jx..1D 

Loopback 

1 

1 

1 

0 

RS232 

1 

1 

0 

0 

RS485 4-wire  / 
Multidrop 

0 

1 

0 

1 

RS485 2-wire 

0 

1 

1 

1 

Low Power Shutdown 

0 

0 

0 

0 

DO NOT USE ANY OTHER COMBINATIONS THAN THE ABOVE 

 
1=Jumper on 
0=jumper removed 
 

17.6  Power-on Tri-state for Xtreme/PCI-104 Opto 12 Port 

 

These models offer a power-on tri-state feature to ensure glitch-free power-up on multi-drop 
networks. When enabled, the Xtreme/104-

 

Opto will hold the RS-485 transmitter in tri-state at 

power up. This feature is available on ports configured as RS-485 half duplex or RS-485 4-wire 
multi-drop.  
 
Note: Enabling this feature on ports configured in RS-232 or RS-422 (RS-485 full duplex) 
modes will alter the operation of the RTS signal. 
 
Jumper 

G-485

 in J2 controls the power-on tri-state functionality.  Install a jumper on this jumper 

to enable the Power on Tri-State function..  
 
 
 

Summary of Contents for PCI-104











































Reviews:

No comments

Brands by name

Popular brands

Load more brands