CONIC LB612FC User Manual Download Page 3

1 x Light  
1 x Power cable 
1 x User manual

 

Danger Light Radiation! 
Avoid direct eye exposure!

 

 

Light radiation can cause eye damage or skin damage 
All protective measures for a safe operation of this light must 
be applied. 

Installation

 

1. Please check the voltage whether is the same with the one 
showed on the equipment.  
2. It must ask for the technical person and set the light safety when 
installation. And let the light beam at the suitable angle.  
3. When install this equipment please make sure there's no 
flammable surfaces (decorated things, etc) within at least 2.5M and 
maintain minimum distance of 0.5M from the equipment to the walls.  
4. Please make sure that there's no other equipment or decorating 
materials obstructed the exhaust fan and the vent-pipe.  
5. Products should be install immobility.  
6. In case of safety, it's very important that to connect ground wire. 

Attention 

1.Please do not open the bottom cover yourself without permission. 

Operate it accord the user manual. Call the technician when the 
machine breaks down.  

2.Please do not see the light beam directly to avoid any damage.  
3.Before connect or disconnect the power, please adjust the 

luminance of the light diode to the least to avoid any damage to the 
light diode.  

4.This unit should be keep dry, do not use in the rain and dusty 

environment. It can be use in the outdoor with the water-proof 
cover .  

5. Set the light immobility and try to avoid strong shake or hit.  
6. Prevent dust into the equipment to avoid problems.  

3

Summary of Contents for LB612FC














Reviews: