Congo Play Bridge and Tower Add-On Assembly Instructions Manual Download Page 3

General Information 

Manufacturer: 

Congo Play, LLC 

180 Rutherford Rd 

G

reenville, 

S

C 29609

rel: 877-494-:3875 

Unit Type: 

Bridge and Tower Add-On 

MAXIMUM FALL HEIGHT: 7'-9" 

THIS PRODUCT IS INTENDED FOR USE 5Y 

CHILDREN FROM AGES 3 TO 10 

This product is intended for single family/residential use only and is not intended for use in any public setting. 

Placement in any public setting constitutes 

misuse of this product. 

CHILDREN MUST NOT USE THE PLAYSYSTEM UNTILL IT 15 COMPLETLEY A55EM5LED, 

PROPERLEY INSTALLED AND INSTRUCTED ON SAFE OPERATION. 

The entire manual should be read before beginning the assembly process. This will minimize installation 

problems and safety issues. 

Operating Instructions 

0&SERVING THE FOLLOWING STATEMENTS AND WARNINGS REDUCES THE LIKELIHOOD OF SERIOUS OR FATAL INJURY. 

1. This playsystem is designed for the use of up to :3 occupants 

on 

the play deck 

or 

swing beam who 

have a 

combined weight

not exceeding :325 lbs.

2. On-site adult supervision is req,uired for children 

of 

all ages.

:3. Instruct children not to walk close to, in front 

of, 

behind, 

or 

between moving items.

4. Instruct children not to twist swing chains 

or 

ropes 

or 

loop them 

over 

the top 

of 

the support bar. This may reduce the

strength 

of 

the chain 

or 

rope.

5. Instruct children to avoid swinging empty seats.

6. Teach children to sit in the 

center of 

the swings with their full weight 

on 

the seat. 

Never 

stand 

on a 

swing.

7. Instruct children not to use the eq,uipment in 

manner other than intended.

8. Instruct children not to get off eq,uipment while it is in motion.

9. Dress children appropriately ( examples would include the use 

of 

well-fitting shoes and the avoidance 

of 

ponchos, scarfs,

and other loose-fitting clothing that is potentially hazardous while using eq,uipment).

1 O. Instruct children not to climb when the eq,uipment is wet. 

11. Verify that suspended climbing ropes, chain, 

or 

cable 

are 

secured a both ends.

12. Verify that suspended climbing ropes, chain, 

or 

cable 

cannot 

be looped back 

on 

itself.

1 :3. Instruct children not to attach items to the playground eq,uipment that 

are 

not specifically designed for use with the

eq,uipment, such as, but not limited to.jump ropes, clothesline, pet leashes, cables and chain as they may cause 

strangulation hazard. 

14. Instruct children to always 

go 

down slides 

feet 

first. 

Never go 

down a slide headfirst.

15. Instruct children to look before going down 

slide to ensure that the slide is clear.

16. Instruct children to 

never 

run up slides.

Summary of Contents for Bridge and Tower Add-On










































Reviews: