background image

Copyright 

© 

2022 

congatec 

AG 

 

      HEVAm100 

 

      

49/54

4.17 

Feature Connector

The conga-HPC/EVAL-Server provides feature connector X43. The pinout is described below: 

Table 48   X43 Pinout Description

Pin Signal

Description

Pin Signal

Description

1

+V5S

5V main supply (0.75 A fuse)

2

+V5A

5V standby supply (0.75 A fuse)

3

SUS_CLK

Clock used by carrier board 

peripherals such as M.2 cards in 

their low power modes.

4

RAPID_

SHUTDOWN

Trigger for rapid shutdown. Must be driven to 5V 

through a <=50 ohm source impedance for ≥ 20 µs. 

Pull-down or disable on module if pin is not asserted.

5

TAMPER#

Tamper or intrusion detection line 

on VCC_RTC power well. Carrier 

hardware pulls this low on a 

Tamper event.

6

SUS_S4_S5#

Active low output that indicates the system is in 

Suspend to Disk (S4) or Soft  Off (S5) state. 

7

PS_ON#

ATX power supply on (active low)

8

CARRIER_HOT#

Input from off-module temperature sensor indicating 

an over-temperature situation.

9

SUS_S3#

Suspend to RAM state (active low 

output)

10

N.C

Not connected

11

THERMTRIP#

Active low output indicating that 

the CPU has entered thermal 

shutdown.

12

WAKE1#

General purpose wake up signal. It may be used 

to implement wake-up on PS2 keyboard or mouse 

activity.

13

WD_OUT

Output indicating that a watchdog 

time-out event has occurred. 

14

N.C

Not connected

15

WD_STROBE# Strobe input to watchdog timer.

16

VIN_PWROK

Power OK from main power supply. A high value 

indicates that the power is good. 

17

BATLOW#

Indicates that external battery is 

low.

18

N.C

Not connected

19

UART0_TX

COM module’s serial port 0 

transmit line

20

UART1_TX

COM module’s serial port 1 transmit line

21

UART0_RX

COM module’s serial port 0 receive 

line.

22

UART1_RX

COM module’s serial port 1 receive line

23

TEST#

Module input for vendor-specific 

module test mode(s).

24

N.C

Not connected

25

GND

Power ground

26

GND

Power ground

 

Connector Type

X43: 2 mm, 2 x 25-pin header

X43

Pin 1

Pin 25

Pin 2

Pin 26

Summary of Contents for conga-HPC/EVAL-Server























































Reviews: