Congatec conga-HPC/EVAL-Server User Manual Download

Page: 30 / 54

2022

congatec

HEVAm100

30/54

4.2.5

Board to Board Connector

The conga-HPC/EVAL-Server provides a board to board connector X42 for connecting congatec KR Ethernet adapters (LEK1, LEK2 and LEK3).
For more information about the congatec KR Ethernet adapters, see the congatec LEK Quick Start Guide.

Table 18 X42 - Ethernet Mezzanine Card Connector Pinout

Signal

Pin Signal

Signal

GND

ETH0_RX-

GND

ETH0_SDP

GND

ETH0_TX-

GND

ETH0-3_INT

GND

ETH1_RX-

GND

ETH1_SDP

GND

ETH1_TX-

GND

ETH0-3_I2C_DAT

GND

ETH0-3_I2C_CLK

A10

GND

B10 ETH2_RX-

C10 GND

D10

ETH2_SDP

A11

B11 GND

C11 NC

D11

GND

A12

ETH2_TX-

B12 GND

C12 NC

D12

ETH0-3_MDIO_DAT

A13

GND

B13

C13 GND

D13

ETH0-3_MDIO_CLK

A14

GND

B14 ETH3_RX-

C14 GND

D14

ETH3_SDP

A15

B15 GND

C15 NC

D15

ETH0-3_PHY_INT#

A16

ETH3_TX-

B16 GND

C16 NC

D16

ETH0-3_PHY_RST#

A17

GND

B17

C17 GND

D17

ETH0-3_PRSNT#

A18

GND

B18 ETH4_RX-

C18 GND

D18

ETH4_SDP

A19

B19 GND

C19 NC

D19

GND

A20

ETH4_TX-

B20 GND

C20 NC

D20

ETH4-7_INT#

A21

GND

B21

C21 GND

D21

GND

A22

GND

B22 ETH5_RX-

C22 GND

D22

ETH5_SDP

A23

B23 GND

C23 NC

D23

GND

A24

ETH5_TX-

B24 GND

C24 NC

D24

ETH4-7_I2C_DAT

A25

GND

B25

C25 GND

D25

ETH4-7_I2C_CLK

A26

GND

B26 ETH6_RX-

C26 GND

D26

ETH6_SDP

A27

B27 GND

C27 NC

D27

GND

X42

Summary of Contents for conga-HPC/EVAL-Server





















































Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands

Congatec conga-HPC/EVAL-Server, User Manual

Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands