Congatec COM Express conga-TCA User Manual Download Page 73

Page: 73 / 94

2012

congatec

TCEDm10

73/94

9.4.1

Graphics Submenu

Feature

Options

Description

Boot Display Device

VBIOS Default

CRT

LFP

DDI

CRT + LFP

CRT + DDI

LFP + DDI

Select the Primary IGD display device(s) to be used during boot up.

CRT: selects Analog VGA display port.

LFP (Local Flat Panel): selects a LVDS panel connected to the integrated LVDS port.

DDI (Digital Display Interface): selects a digital interface HDMI or DP connected to the system.

Active LFP

No LVDS

LVDS

Select the active local flat panel configuration.

Always Try Auto Panel
Detect

Yes

If set to ‘Yes’ the BIOS will first look for an EDID data set in an external EEPROM to configure the Local Flat

Panel . Only if no external EDID data set can be found, the data set selected under ‘Local Flat Panel Type’ will

be used as fallback data set.

Local Flat Panel Type

Auto

VGA 640x480 1x18 (002h)

VGA 640x480 1x18 (013h)

WVGA 800x480 1x24 (01Bh)

SVGA 800x600 1x18 (01Ah)

XGA 1024x768 1x18 (006h)

XGA 1024x768 1x24 (008h)

WXGA 1280x768 1x24 (01Ch)

Customized EDID™ 1

Customized EDID™ 2

Customized EDID™ 3

Select a predefined LFP type or choose Auto to let the BIOS automatically detect and configure the attached

LVDS panel.

Auto detection is performed by reading an EDID data set via the video I²C bus.

The number in brackets specifies the congatec internal number of the respective panel data set.

Note: Customized EDID™ utilizes an OEM defined EDID™ data set stored in the BIOS flash device.

Flat Panel Scaling

Auto

Forced Scaling

Off

Maintain Aspect Ratio

Select the Flat Panel Scaling mode.

Backlight Inverter Type

None

PWM
I2C

Select the type of backlight Inverter used.

IGD Clock Source

External clock

Internal Clock

IGD clock selection

IGD Total Graphics
Memory

128MB

256MB

Select the amount of total graphics memory that maybe used by the Internal Graphics Device. Memory

above the fixed graphics memory will be dynamically allocated by the graphics driver according to DVMT 5.0

specification.

ALS Support

Disabled

Enabled

Valid only for ACPI

Enable ALS support on the Operating System.

Digital Display Interface 1

Disabled

Display Port
HDMI/DVI

Select the Digital Display Interface offered by the DDI 1

Summary of Contents for COM Express conga-TCA































































































Search results

Summary of Contents for COM Express conga-TCA

Reviews:

Brands by name

Popular brands

Congatec COM Express conga-TCA, User Manual

Search results

Summary of Contents for COM Express conga-TCA

Reviews:

Brands by name

Popular brands