background image

Copyright 

© 

2022 

congatec 

GmbH 

 

      CET0m10 

       

4/58

Intended Audience

This user’s guide is intended for technically qualified personnel. It is not intended for general audiences.

Lead-Free Designs (RoHS)

All congatec GmbH designs are created from lead-free components and are completely RoHS compliant. 

Electrostatic Sensitive Device 

All congatec GmbH products are electrostatic sensitive devices. They are enclosed in static shielding bags, and shipped enclosed in secondary 
packaging (protective packaging). The secondary packaging does not provide electrostatic protection. 

Do not remove the device from the static shielding bag or handle it, except at an electrostatic-free workstation. Also, do not ship or store 
electronic devices near strong electrostatic, electromagnetic, magnetic, or radioactive fields unless the device is contained within its original 
packaging. Be aware that failure to comply with these guidelines will void the congatec GmbH Limited Warranty.

Copyright Notice

Copyright © 2022, congatec GmbH. All rights reserved. All text, pictures and graphics are protected by copyrights. No copying is permitted 
without written permission from congatec GmbH. 

congatec GmbH has made every attempt to ensure that the information in this document is accurate yet the information contained within is 
supplied “as-is”.

Trademarks

Product names, logos, brands, and other trademarks featured or referred to within this user’s guide, or the congatec website, are the property 
of their respective trademark holders. These trademark holders are not affiliated with congatec GmbH, our products, or our website.

Summary of Contents for COM Express conga-MEVAL



























































Reviews: