Congatec COM Express conga-BM67 User Manual Download Page 80

Page: 80 / 101

2011

congatec

BM67_BS67m02

80/101

8.6

PCI Bus Masters

The conga-BM67/BS67 supports 4 external PCI Bus Masters. There are no limitations in connecting bus master PCI devices.

Note

If there are two devices connected to the same PCI REQ/GNT pair and they are transferring data at the same time then the latency time of

these shared PCI devices can not be guaranteed.

8.7

I²C Bus

There are no onboard resources connected to the I²C bus. Address 16h is reserved for congatec Battery Management solutions.

8.8

SM Bus

System Management (SM) bus signals are connected to the Intel

BD82QM67 or BD82HM65 (QM67 or HM65) PCH and the SM bus is not

intended to be used by off-board non-system management devices. For more information about this subject contact congatec technical support.

Summary of Contents for COM Express conga-BM67






































































































Search results

Summary of Contents for COM Express conga-BM67

Reviews:

Related manuals for COM Express conga-BM67

Brands by name

Popular brands

Congatec COM Express conga-BM67, User Manual

Search results

Summary of Contents for COM Express conga-BM67

Reviews:

Related manuals for COM Express conga-BM67

Brands by name

Popular brands