background image

Page5

Direction Switch on fan body controls air movement:

Caution: Before using the direction switch, turn the fan OFF and ensure that the fan has stopped rotating to

prevent injury to yourself and damage to the motor.
Cold weather :  Push switch UP for the blades to move the warm air trapped near the ceiling.
Hot weather :  Push switch DOWN for the blades to create a breeze and circulate the air.
The light on/off can be controlled by pressing light "ON/OFF" button on the remote control transmitter.

 Remote control

Use the infra-red remote control to change the speed of the fan and to switch the light and fan off.

The remote control to work properly
Replace the batteries by sliding the battery compartment panel on the remote in the direction of the arrow, fit

2 x "AAA" batteries, ensuring polarity as shown in the batter compartment. (Note: Batteries NOT included). Slide

on the battery compartment cover.
ALWAYS ensure that the battery compartment panel is secure.
NEVER leave the remote control in direct sunlight.
NEVER attempt to recharge primary batteries, either in a charger or by applying heat to them. There are special

rechargeable batteries which are clearly marked as such.
NEVER dispose of batteries in fire, because this can cause them to explode.

Install the glass shade onto the lamp kit 
by rotating the glass shade clockwise.

33. Glass Shade

Summary of Contents for FLORIDA R52001-5-1L













Reviews: