Door Sensor User Manual
*
Please read the manual carefully before operating
Product Introduction
Door sensor is an intelligent security equipment that can transmit through Z-wave network and radio
waves. In the Z-wave network communications, door sensor can be connected to any Z-wave gateway.
Door sensor can send messages to Z-wave gateway, then realize association with other devices. Different
countries or areas, the radio frequency is different.
Each door sensor has a unique ID code. When we add or remove door sensor from gateway, just place it in
the z wave network range of gateway. Then we can easily find the door sensor through device ID code.
In
the
communication
with
Z-wave gateway, door sensor can
only send
messages to Z-wave
gateway,
but can not
receive
messages. When alarm is triggered, door sensor would send messages to
gateway, then Z-wave gateway would display the current status of door sensor. At the same time, door
sensor can realize association with other devices through z wave gateway. Door sensor is powered by
batteries, with small body , and can be installed on the window or door easily. When door or window is
open, door sensor would be triggered, then associates with other devices to work, to realize the goal of
safety protection.
TECHNICAL SPECIFICATIONS
TECHNICAL PARAMETERS
Power
CR2-3V x1
Standby Current
1uA
Battery Life
1 Year
Radio Protocol
Z-wave
Radio Frequency
865.2MHz IN
Compatible with
300 Series and 500 Series
Wireless Distance
Upto 60m Outdoor, Upto 30m Indoor
Operation Temperature
0- 45
℃
Storage Temperature
0 -60
℃
Size
Door sensor main body (L x W x H):
71mmX20mmX22mm
Door sensor deputy body (L x W x H):
40mmX11mmX11mm
TECHNICAL INFORMATION
Installed on the door or window
Battery powered
Easily installed with screws or sticker
Associate with other devices through gateway
Compatible with any Z-wave network
Product Configuration
Figure 1
Items List
Door sensor main body - 1No.
Door sensor deputy body - 1No.
Battery - 1No.
Screw - 4Nos.
Screw Stopper - 4Nos.
Sticker -2Nos.
User Manual - 1No.
Installation Steps
Door Sensor Installation.
Battery Installation.
Door Sensor Installation
Step 1 :
Dismantle the door sensor main body and take out the battery, fix the main body on the door with
screws.
Dismantle the door sensor deputy body and fix it on the corresponding door frame position.
Figure 2
Step 2 :
Put the sticker on the bottom of door sensor then fix it on the wall
Figure 3
Note:
When installing door sensor, door
sensor deputy body must be installed on the bulge side of the
door
sensor main body.
Battery Installation
Figure 4
Tips
When installing the door sensor, the distance between main body and deputy body should be less
than 2cm in the state of door closed.
When door is closed, that is to say, distance between main body of door sensor and deputy body
is less than 2cm, app would display door is closed.
When door is opened, that is to say, distance between main body of door sensor and deputy body
is more than 2cm, the app would display the door is opened. Through gateway, door sensor can
associate with IP camera to take pictures and record video, siren to alarm.
Make sure door sensor is placed in the Z-wave network range of gateway.
Battery Usage Tips
Battery life of door sensor is approximately 1 year. The power level of battery would be displayed in the
gateway. Red icon means the battery needs replacing, and then mobile app would receive a message
“
Power level is low, Please remember to replace battery
”
from gateway. In order to avoid false alarm,
before replacing battery, please disconnect association of door sensor with other devices.
Note:
Door sensor is powered by battery, and please use battery in a correct way to avoid exploding.
When handling the battery, refer to environmental law please.
The status of LED
1.
When door sensor is triggered, LED lights would flash red color 1 time.
2.
When door sensor is installed with battery, LED lights would flash red color 5 times.
3.
Add or Remove door sensor from Z-wave network by quickly pressing the button 3 times , then
LED lights would flash red color 5 times.
4.
Press and Hold the code button for 10-15 seconds, then door sensor would be restored to factory
default settings. Meanwhile, LED lights would flash red color 5 times on and off alternately.
5.
Under the normal state, LED lights would keep
“
off
“
state.
