Step 1.
Snap stringers
into bottom tread.
If necessary lift
the two stringers
off the ground,
with the bottom
tread attached,
and drop them
firmly so that the
stringers “snap”
into the tread
pockets. The
bottom tread
should pivot
freely.
Make sure the
single row of
tread lugs are
facing forward.
Tread Lugs
Step 2.
Two sets of Lug
locations are provided.
Attach 4 upper treads
to the stringers in the
position determined by
the pool height.
Tread Lugs
Step 3.
Step 4.
Using a pair of pliers twist off
the wedges that are attached
from the end of the platform
and
SAVE
for use in step 5.
Wedges
Protrusion
Detach
Wedges
Use upper
lugs for
50" to 54" pools.
Use lower
lugs for
42" to 48" pools.
Secure the
upper treads
by driving
#10 x 1-1/4"
screws through
the recessed,
pre-drilled holes
in the ends of
each tread as
shown. Repeat
for all 4 upper
treads.
Step 5.
Assemble the platform to
the handrails by laying
one of the handrails on a
clean hard surface. Push
the protrusion of the plat-
form into the openings of
the handrail making sure
that the legs of both
handrails are facing in the
same direction. Tap the
4 wedges (from step 4)
into the sides of the
handrails to secure the
platform to the rails.
Step 6.
If needed, coat tubes
with liquid soap or
lubricant and slip the
adjustable tubes
through the mounting
blocks all the way
down over the
protruding nubs.
Mounting Block
Adjustable tube
Slide mounting
blocks over nubs
Step 7.
Step 8.
Stringers
Step 9.
Step 10.
Snap Small and Large Barrier Sections into slots
on Lower Base as shown.
Step 11.
Separate sections at
the top slightly and
position Upper Brace
over Small Barrier
Section.
Next, spread the
“fingers” on the Upper
Brace into position on
the Large Barrier
Section as shown.
Step 12.
Step 13.
Attach the handrails to
the ladder assembly,
making certain that the
treads face correctly.
Match
Platform
protrusions
to Handrail
openings
After platform is in
position, tap in the
supplied wedges at
the bottom of each
opening to ensure a
secure fit
Push the
adjustable tubes
with mounting
blocks into
handrails.
Fill both stringers with water to
allow the ladder to be submerged
in the pool.
Push
down
2
3
Hardware Pack
26 - #10 x 1-1/4" screws
2 - Mounting Blocks
2 - Adjustable Tubes
Tools Needed for Assembly
* - Cordless Drill Motor
* - 1/8" Drill Bit
* - Phillips Screwdriver
or screwdriver bits
* - Pliers
* - Garden Hose
* - Liquid soap or lubricant
Barrier Parts List (if included)
(Included in Hardware Pack)
4 -
#10 x 1-1/4” screws
1 -
Strip of 4 Foam Pads
1 -
Large Barrier Section
1 -
Small Barrier Section
1 -
Upper Brace
1 -
Lower Base
Model #6000
Adjustable Heavy-Duty Inpool Ladder
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Parts List
2 - Handrails
2 - Stringers (Legs)
4 - Upper treads
1 - Bottom tread
1 - Platform with Wedges
(See Step 4)
If missing parts call - Toll free U.S. - 866-396-2968 or www.conferladders.com
NOTE: To winterize your ladder, remove it from the pool and drain water from stringers and treads.
Step 14.
Step 15.
C.
Drill a 1/8" pilot hole
through the handrail ends at
the pre-marked locations into
the stringers and repeat
this step for the adjustable
tubes and mounting blocks.
Place the ladder in
the desired position
on the deck and
slide the ladder
assembly down until
the bottom tread
meets the pool liner.
Slide the adjustable
tubes with the
mounting blocks as
needed to position
the ladder correctly
on the deck.
Make sure the
bottom tread is
flush with the
pool liner.
Ladder
Assembly.
Slide
adjustable
tubes to
position
against deck.
B.
Using a
cordless drill
attach the
mounting
blocks with
eight (8)
#10 x 1-1/4"
screws.
A.
Secure the handrail using
four (4) #10 x 1-1/4" screws
at the pre-marked locations
(two per handrail).
D.
Secure the handrail to the
tubes using four (4) #10 x 1-1/4"
screws at the pre-marked
locations (two per handrail).
Submerge in
water and tilt to a
15° angle to allow
water to fill the
treads.
Note: Ladder
treads must fill
with water to
prevent floating
If Ladder did not include Barrier, skip steps 10 through 12. Continue to step 13.
Fingers
Large
Barrier
Screws
Foam
Pads
Small
Barrier
WEDGE
HANDRAIL
PLATFORM
ADJUSTABLE
TUBE
UPPER
TREAD
MOUNTING
BLOCK
STRINGER/
LEG
BARRIER
SECTION
BOTTOM
TREAD
Place the Base and
Brace into position,
centered, on the bottom
and fourth treads of the
ladder. Install the four
(4) #10 x 1-1/4” screws
(included in hardware
pack), on a slight angle,
first in the Upper Brace,
and then in the Lower
Base as shown. Install
the self-adhering foam
strips to the Large
Barrier Section
as shown.
Confer 6000_R8:Confer 6000_R1 12/5/07 1:29 PM Page 3