background image

 
  

ROUTER

 

DESCRIPTION

 

5.6.  Mechanical external dimensions and mounting 

recommendations 

Mounting recommendations: 

  possibility to be put on a work surface, 

  DIN rail with clips CPD2 (Elpac clip SL for SL version) are included. 

For the most of applications with a built-in router in a switch board it is possible 

to recognize two kinds of environments: 

 

no public and industry environment of low voltage with high i

 

public environment of low voltage without high interference. 

nterference, 

For both of these environments it is possible to mount router to a switch board, 

the following there is no need to have examination immunity or issues in connection with 
EMC according to EN 60439-1 ed.2:00 + A1:04. 

For compliance of EN 60439-1 ed.2:00 + A1:04 specification it is necessary 

to observe next assembly of the router to the switch - board: 

 

for whip antennas we recommend to observe a distance of 6 cm from cables 
and metal surfaces on every side according to the next picture due to the elimination 
of interference, while using an external antenna except for the switch-board it is 
necessary to fit a lightening conductor, 

 

before mounting a router on sheet-steel we recommend using an external antenna, 

 

 

Fig. 12: Space around the antenna 

 

Fig. 13: Space around antenna for SL version 

 

Summary of Contents for UR5i v2 SL

































Reviews: