background image

33

Fault Isolation

Condair TE

  

7.5.6 

Abnormal smells coming from the humidifier

Remote Controller 

Display

Possible Cause of Failure

Action

Normal indicator 

light displays

Supply water quality is poor

Confirm and rectify Clean or replace 

the humidification module

The humidifier unit is not level, so water has accumulated in 

the drain pan

Confirm and rectify Clean or replace 

the humidification module

The odor is caused by air flow infiltration from the waste water 

drainage piping

Rectify the problem by separating 

drainage piping from other piping or 

taking similar measures

The humidification module has become dirtied through use

Clean or replace the humidification 

module

A reason not listed above

Contact Condair

7.5.7 

White powder (lime scale) is dropping from the humid. module

Remote Controller 

Display

Possible Cause of Failure

Action

Normal indicator 

light displays

Water quality does not fulfill the requirements listed in the 

product specifications

Confirm and rectify; if necessary, 

clean or replace the humidification 

module

Holes in the water supply strainer are clogged, which reduces 

supply water volumes

Clean the water supply strainer, clean 

or replace the humidification module

Supply water pressure is too low, resulting in insufficient sup

-

ply water volumes

Confirm and rectify; if necessary, 

clean or replace the humidification 

module

The water supply header has become clogged, resulting in 

insufficient supply water volumes

Clean the water supply header 

nozzle(s)

The air temperature of the humidifier unit's intake air is too 

high (current supply water volume is insufficient for the in

-

creased humidification demand)

Increase the supply water volume, 

clean or replace the humidification 

module

A reason not listed above

Contact Condair

Summary of Contents for TE Series













































Reviews: