Condair GC 130 Operation And Maintenance Manual Download Page 40

Page: 40 / 72

Operator Interface

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

3. Select from "0-5V", "1-5V", "0-10V", "2-10V", "0-20V", "0-16V", "3.2-16V", "0-20mA", or "4-20mA",

as appropriate for the external control device connected to Channel 1.

This concludes the basic setup of the control software.

4.3.2

Configuring for Multi-Unit Operation

Set up the control software for multi-unit operation as described below. A maximum of four humidifiers

can be set up in a "Main-Extension" configuration using Condair's Linkup system to satisfy large hu

midification needs.

IMPORTANT!

This procedure should only be used to control multiple humidifiers that are using the

same control signal inputs from the same conditioned environment.

1. Make sure that all wiring and jumpers are installed, as described in "Connecting Multiple Units Using

Linkup" in the Installation Manual.

2. Configure the main humidifier as described in

"Configuring the Control Software" on page 39

Set

Linkup

to "Main" on the humidifier that will be designated as Main in the Linkup chain, and set

up the following parameters on it:

Linkup Units

– select the total number of humidifiers in the Linkup chain. For example, if there is

one main unit and two extension units, then the total number of humidifier in the chain is 3.

Linkup Type

– select the mode of operation of the humidifiers in the Linkup chain ("Series" or

"Parallel").

Sequence Rotation

– enable or disable the function that manages the starting order to balance the

operating hours on each steam cylinder. Note: This setting is available only if

Linkup Type

is set

to "Series".

Sequence Interval

– set the time interval used by the control software to establish a new operating

sequence to balance the operating hours on the steam cylinders in the Linkup chain.

Linkup Timeout

– if required, change the maximum time limit that the units in the Linkup chain can

operate without a connection to each other before they generate a Linkup Timeout warning

message.

Zero Out

– if required, set the percentage value of the system demand signal at which the unit is

switched on.

Full Out

– if required, set the percentage value of the system demand signal at which the unit

achieves 100% demand.

Set

Linkup

in each extension humidifier as Ext1, Ext2, ...

Note

: Each extension unit must be a unique extension number.

The humidifiers in the Linkup chain are now set up to generate steam upon humidity demand.

Summary of Contents for GC 130









































































Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands

Condair GC 130, Operation And Maintenance Manual

Search results

Summary of Contents for GC 130

Reviews:

Related manuals for GC 130

Brands by name

Popular brands