72
73
EN
EN
KV0800 / KV1000
KV0800 / KV1000
The display shows an error
message “E2”.
The room temperature sensor signals an
unusual value.
Clean the filters and switch the appliance
on again. If the problem persists, contact
a service centre.
The display shows an error
message “FL”.
The water tank inside the appliance is
full.
Drain the water from the drain opening
at the bottom back of the appliance.
Other
No refrigerant or just a very small
amount of refrigerant.
Contact the service centre (check for
leaks, connections, extract and fill with
refrigerant according to the type plate).
Frost protection.
Waiting for defrost. The function resumes
automatically. No user intervention is
required.
High pressure protection.
As soon as the internal gas pressure
drops, the function will be normal. No
user intervention is required.
If problems occur which are not listed in the table or the recommended solutions do not work, contact a service
centre.
SERVICE CENTRE
Extensive maintenance or repair, which requires access to internal parts of the product, has to be performed by
a qualified specialist or the service centre.
ENVIRONMENTAL CONCERNS
•
Packaging materials and old appliances should be recycled.
•
Packaging materials may be disposed of as sorted waste.
•
Dispose the plastic bags made of polyethylene (PE) of as sorted waste.
Recycling of the appliance at the end of its lifespan:
This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical
and electronic appliances (waste electrical and electronic equipment - WEEE). The symbol on the product
or on its packaging indicates that this product may not be treated as household waste. Instead, it should
be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling
of this product. The disposal of such material has to be done according to the recycling regulations. For
more detailed information about recycling of this appliance see the authorized local office or service for
household waste disposal or the shop, where you purchased the appliance.
The product meets all the necessary requirements of the EU directives applicable to the specific product.
Changes in text, design, and technical specifications are subject to change without prior notice and we reserve the right
to change them.
TROUBLESHOOTING
Do not repair or disassemble the air conditioning unit yourself. Unauthorized repair will void the warranty and may result
in failure, injury, and property damage. Use the appliance only in accordance with the instructions in this user manual
and only carry out the activities recommended here.
Problem
Cause
Remedy
The air conditioning unit
does not work
The electricity is not switched on.
After connecting to the mains, switch on
the appliance.
The overflow indicator light shows “FL”.
Drain the water from the inner tank.
The ambient temperature is too low or
too high.
Use the appliance only in the
temperature range 7-35 °C (44-95 °F).
In cooling mode, the room temperature
is lower than the set temperature; in
heating mode, the room temperature is
higher than the set temperature.
Change the temperature setting.
In dehumidification mode, the ambient
temperature is low.
The appliance is located in a room with
an ambient temperature higher than
17 °C (62 °F).
The cooling effect is not
good
Direct sunlight.
Use curtains to reduce direct sunlight.
Doors or windows are open. Many
people are present or there are
other heat sources in the room (e.g.
refrigerator) in cooling mode.
Close doors and windows, increase air
conditioning unit performance.
The filter insert is dirty.
Clean or replace the filter insert.
Air inlet or outlet is blocked.
Remove any obstructions and make sure
the ventilation is correct as described in
this user manual and the hose is not too
bent.
Loud sound
The air conditioning unit is not located
on a flat surface.
Place the air conditioning unit on a flat
and stable surface (to reduce noise).
The compressor does not
work
Overheat protection has been activated.
Wait 3 minutes for the temperature to
drop, then switch on the appliance again.
The remote control does
not work
The distance between the appliance and
the remote control is too long.
Move the remote control closer to the air
conditioning unit and make sure that the
remote control is pointed directly in the
direction of the remote control receiver.
The remote control is not aligned with
the direction of the remote control
receiver.
The display shows an error
message “E1”.
The hose temperature sensor signals an
unusual value.
Clean the filters and switch the appliance
on again. If the problem persists, contact
a service centre.
