background image

 

 

Maintenance of your playground  

We hope that you and your family will enjoy many hours of great family fun while using your 
Component Playgrounds Products. We appreciate your business. Our goal is to provide safe, 
durable and fun products using the best materials available. Your product should be mostly 
maintenance free. However, you should consider the following suggestions with regard to the 
up keep of your new swing set.  

1. 

Chains and Connectors: 

The chains are coated with the highest quality bright zinc  

coating and the highest quality polymer coatings available. However, over time the 
zinc coating may become discolored or eventually have surface rust appear. The 
polymer coating may also become discolored with time and may eventually crack. This 
depends mostly upon environmental conditions and normally will not affect the 
durability and safety of the product. However, these items should be inspected 
regularly for excessive wear and should be replaced as necessary.  

2. 

Swing Hangers: 

These items are coated with a high quality galvanizing. However,  

swing hangers may become discolored or may eventually rust. Should this happen, a 
touch up using a cold galvanizing compound followed by a coat of silver aluminum spray 
paint will make them look new again. These items can be purchased in aerosol cans 
(“spray paint”) at most hardware stores and at Component Playgrounds. The brass 
bushings inside of the swing hanger are impregnated with lubricant and will not 
generally require any further lubrication. However, these should be periodically 
inspected for wear and replaced as necessary. Note: Twisting the chains while swinging 
will put extra wear on the swing hanger parts. If your children enjoy this practice, please 
inspect the swing hangers more frequently.  

3. 

Tire Swing Knuckles (for sets with a tire swing): 

The tire swing knuckle arrives at  

Component Playgrounds pre-lubricated from the manufacturer. However, it is good 
practice to inspect the knuckle and be sure that there is adequate lubrication before it 
is used for the first time. After that, the tire knuckles should be lubricated at least twice 
annually to prevent excessive wear and the eventual failure of the tire swing knuckle.  

4. 

Welds: 

The heat from the welding process will damage the galvanizing that is on the  

pipe when it arrives to us from the manufacturer. This damage to the galvanizing is 

Summary of Contents for MT21-10
















Reviews: