background image

restricted to the actual weld. When your equipment is built, Component Playgrounds 
will repair this damage using a cold galvanizing compound spray along with a top coat 
of silver aluminum. This is a time tested and durable process. However, when you are 
inspecting your playground equipment, if you notice that some surface rust has 
appeared on the welds, simply apply a fresh coat of the cold galvanizing compound 
and the silver aluminum top coat to keep your structure looking new. (These spray 
products  
can be purchased in aerosol cans (“spray paint”) at most hardware stores and 
at Component Playgrounds.)  

5. 

Plastic Lumber Platforms: 

If you have purchased a structure which includes a  

platform, the plastic lumber does not need to be finished or stained. It is 100% 
maintenance free. However, you may need to occasionally hose it down to remove 
dirt and other debris that may collect after many hours of use by happy children.  

6. 

Vinyl Canopies: 

If you have purchased a structure which includes a vinyl canopy, this 

product should be inspected occasionally for wear and will need to be replaced as 
necessary. Depending upon your environmental conditions, the normal life 
expectancy of the vinyl canopy is 3 – 5 years.  

7. 

Swing Seats: 

These should be inspected at least twice annually and should be replaced  

as necessary.  

8. 

Slides: 

Slides should never be lifted at the bottom. Lifting the slide at the bottom will  

almost always cause the slide to crack at the top where it has been attached to 
the platform or bracket. Cracks and wear such as is caused by this practice are 
easily identifiable and will not be covered under the product warranty.  

Slides should be inspected at least annually to ensure that the sliding surface is in 
good condition. Also inspect the side rails to be sure that the plastic has not been cut 
or gouged in any manner which would present the risk of injury while sliding.  

9. 

Fasteners: 

All fasteners should be periodically inspected to make certain that they are  

tight and secure. Re-secure as 
necessary.  
 

*For Safety please inspect all moving parts on a regular basis. (At Least Yearly) 

Especially paying attention to wear within the swing hanger.  

 
 

 

Summary of Contents for AF60
















Reviews: