Component Engineering STRD-30S Manual Download Page 4 | Manualshive

Page: 4 / 11

Component Engineering STRD-30S Manual Download Page 4

3

LED assembly

Dual lens/pre-amp assembly

Rear of the LED assembly

The

LED assembly

can now be mounted to the top of the

standoff post by means of three 4-40 Flat Head screws. The
Lateral Guide can also be reinstalled.

The

dual lens/pre-amp assembly

should now be carefully eased

onto the dowel pins in the adapter block and bolted in place. It is
a good idea to have the digital video cable already plugged onto
the digital pre-amp circuit board before you mount this assembly.

Wiring

Connect both of the LED’s to the outputs of the LS-30 power
supply chassis. The small terminal strips at the

rear of the LED

assembly

can be unplugged by pushing away from you. Note that

no polarity is indicated. This is because the LED’s may come
with either polarity and you will have to determine the correct
connection by trial and error. It is safe to do this because the
output of the LS-30 power supplies is clamped at a voltage too
low to damage the LED’s. The recommended wire size is #18
AWG.

«
...
2
3
4
5
6
...
»

Summary of Contents for STRD-30S












Reviews:

No comments