Compex Professional Portable Mixing Console SONOSAX SX-S User Manual Download Page 1

Back to SX-S Page

 

USER MANUAL

PROFESSIONAL PORTABLE

MIXING CONSOLE

SONOSAX SX-S/SX-V

 

Audio equipment manufacturer

ch de la Naz 38

CH-10252 Le Mont / LAUSANNE

SWITZERLAND

Tel (41-21) 651 01 01

Fax (41-21) 651 01 09

 

INTRODUCTION

 

Your SONOSAX SX-S or SX-V mixing console has been manufactured to deliver many years of excellent performance. 

The reliability of the SONOSAX SX-S and SX-V is due to a design combining the highest possible density with meticulous 
hand assembly.

 

This professional mixer of optimum performance and reliability is the result of selection of choice electronic components 

and severe quality control.

 

The information and instructions contained in this manual are necessary to ensure safe operation of your equipment and 

to maintain it in good working condition.

 

NOTE: 

The specifications mentioned hereafter apply to all standard models as of serial numbers SX-S 16150, and SX-V 

120022. 

 

SONOSAX  reserves the right to modify these characteristics at any time without prior notice.

 

  

TABLE OF CONTENTS

  

1.

PREPARATION

 

OPERATING INSTRUCTIONS

 

INPUT MODULE after serial nb 16579

 

STANDARD INPUT MODULE

 

Differences from the newer Power / Mute modules

  

MASTER MODULE

 

SX-S EXTENSION MODULE

 

Seite 1 von 22

SONOSAX SX/S USER MANUAL

26.08.2004

file://D:\Z_Library\Webcopy\sonosax\SXS\sxsume.html

Summary of Contents for Professional Portable Mixing Console SONOSAX SX-S























Reviews: